Official Software
Get notified when we add a new Abarth500 Manual

We cover 20 Abarth vehicles, were you looking for one of these?

Summary of Content
2012 FIAT 500 2012 BLUE&ME™ USER’S MANUAL Chrysler Group LLC 12FBM-726-AC First Edition FIAT 500 Printed in U.S.A. 960648cv1.psp 12FBM-726-AC Fiat 1" gutter 03/23/2011 14:25:37 2012 FIAT 500 2012 BLUE&ME™ USER’S MANUAL Chrysler Group LLC 12FBM-726-AC First Edition Printed in U.S.A. FIAT 500 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation. WARNING! Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive. This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle. Chrysler Group LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured. INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. FIAT is a registered trademark of FIAT Group Marketing & Corporate Communication SpA, used under license by Chrysler Group LLC. Antennas for two-way radios should be mounted on the roof or the rear area of the vehicle. Care should be used in mounting antennas with magnet bases. Magnets may affect the accuracy or operation of the compass on vehicles so equipped. Copyright © 2011 Chrysler Group LLC The positive power connection should be made directly to the battery and fused as close to the battery as possible. The negative power connection should be made to body sheet metal adjacent to the negative battery connection. This connection should not be fused. The antenna cable should be as short as practical and routed away from the vehicle wiring when possible. Use only fully shielded coaxial cable. Carefully match the antenna and cable to the radio to ensure a low Standing Wave Ratio (SWR). Mobile radio equipment with output power greater than normal may require special precautions. All installations should be checked for possible interference between the communications equipment and the vehicle’s electronic systems. 960618cv1.psp 12FF500-126-AD Chrysler 1" gutter 03/28/2011 17:46:33 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation. WARNING! Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive. This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle. Chrysler Group LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured. INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. FIAT is a registered trademark of FIAT Group Marketing & Corporate Communication SpA, used under license by Chrysler Group LLC. Antennas for two-way radios should be mounted on the roof or the rear area of the vehicle. Care should be used in mounting antennas with magnet bases. Magnets may affect the accuracy or operation of the compass on vehicles so equipped. Copyright © 2011 Chrysler Group LLC The positive power connection should be made directly to the battery and fused as close to the battery as possible. The negative power connection should be made to body sheet metal adjacent to the negative battery connection. This connection should not be fused. The antenna cable should be as short as practical and routed away from the vehicle wiring when possible. Use only fully shielded coaxial cable. Carefully match the antenna and cable to the radio to ensure a low Standing Wave Ratio (SWR). Mobile radio equipment with output power greater than normal may require special precautions. All installations should be checked for possible interference between the communications equipment and the vehicle’s electronic systems. BLUE&ME™ User’s Manual 1-888-CIAO-FIAT (1-888-242-6342) CONTENTS 䡵 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ▫ Front Steering Wheel Buttons . . . . . . . . . . . . . 14 ▫ The BLUE&ME™ Hands-Free Communication Package . . . . . . . . . . . . . . . . . 5 ▫ Rear Steering Wheel Buttons . . . . . . . . . . . . . 14 ▫ Message Reader . . . . . . . . . . . . . . . . . . . . . . . 8 䡵 BLUE&ME™ Hands-Free Communication Package Quick Reference Guide . . . . . . . . . . . . . 18 ▫ Media Player . . . . . . . . . . . . . . . . . . . . . . . . 10 ▫ Prepare Your Mobile Phone Phonebook . . . . . . 18 ▫ Road Safety . . . . . . . . . . . . . . . . . . . . . . . . . 11 ▫ Important Notes . . . . . . . . . . . . . . . . . . . . . . 18 䡵 Display And Buttons On The Steering Wheel . . . 13 ▫ Try Out The Voice Commands . . . . . . . . . . . . 19 ▫ Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ▫ Pair Your Mobile Phone . . . . . . . . . . . . . . . . . 20 1 2 BLUE&ME™ User’s Manual ▫ Making a Phone Call . . . . . . . . . . . . . . . . . . . 21 䡵 Message Reader Quick Reference Guide 䡵 Media Player Quick Reference Guide ▫ Incoming Calls . . . . . . . . . . . . . . . . . . . . . . . 38 . . . . . . 22 ▫ Managing Phone Calls . . . . . . . . . . . . . . . . . 39 . . . . . . . . 22 ▫ Conference Call Function . . . . . . . . . . . . . . . . 40 䡵 How To Use BLUE&ME™ Hands-Free 䡵 Message Reader Functions . . . . . . . . . . . . . Communication . . . . . . . . . . . . . . . . . . . . . . . . 24 ▫ How To Read The Last SMS Text Received ▫ Steering Wheel Controls . . . . . . . . . . . . . . . . 24 ▫ Inbox . . . . . . . . . . . . . . . . . . . . . . . . . . . ▫ Voice Commands . . . . . . . . . . . . . . . . . . . . . 24 ▫ Managing Messages . . . . . . . . . . . . . . . . ▫ Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 ▫ Deleting All Messages . . . . . . . . . . . . . . . ▫ Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 ▫ SMS Notification Settings . . . . . . . . . . . . ▫ BLUE&ME™ Hands-Free Communication 䡵 Media Player Functions . . . . . . . . . . . . . . . Function Menu . . . . . . . . . . . . . . . . . . . . . . . 29 ▫ How To Connect The USB Device/iPod To 䡵 BLUE&ME™ Hands-Free Communication BLUE&ME™ Hands-Free Communication . Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 ▫ How To Manage The Media Library . . . . . ▫ Making a Phone Call . . . . . . . . . . . . . . . . . . . 32 . . . 41 . . . 42 . . . 42 . . . 43 . . . 43 . . . 44 . . . 45 . . . 46 . . . 47 BLUE&ME™ User’s Manual 3 ▫ Playing Audio Tracks . . . . . . . . . . . . . . . . . . 52 ▫ Hands-Free Communication Package . . . . . . . 83 ▫ Practical Hints For Using The Media Player . . 55 ▫ Message Reader . . . . . . . . . . . . . . . . . . . . . . 91 䡵 Setting Functions . . . . . . . . . . . . . . . . . . . . . . . 56 ▫ Media Player . . . . . . . . . . . . . . . . . . . . . . . . 94 ▫ Pairing a Mobile Phone . . . . . . . . . . . . . . . . . 57 ▫ iPod威 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 ▫ Managing User Data . . . . . . . . . . . . . . . . . . . 62 䡵 Personal Data Protection . . . . . . . . . . . . . . . . 101 ▫ Advanced Options . . . . . . . . . . . . . . . . . . . . 65 䡵 System Software Use Notice . . . . . . . . . . . . . . 101 ▫ Media Player Settings . . . . . . . . . . . . . . . . . . 66 ▫ End User License Agreement (“EULA”) . . . . 102 䡵 BLUE&ME™ Hands-Free Communication Supported Mobile Phones . . . . . . . . . . . . . . . . . 68 ▫ Grant Of Software License. This EULA Grants You The Following License . . . . . . . . 102 ▫ Mobile Phones With Bluetooth威 Wireless Technology . . . . . . . . . . . . . . . . . . . . . . . . . . 69 ▫ Description Of Other Rights And Limitations . . . . . . . . . . . . . . . . . . . . . . . . . 103 ▫ Supported USB Memory Devices . . . . . . . . . . 70 ▫ Upgrades And Recovery Media . . . . . . . . . . 106 䡵 List Of Available Voice Commands . . . . . . . . . . 74 ▫ Intellectual Property Rights . . . . . . . . . . . . . 106 䡵 Troubleshooting ▫ Export Restrictions . . . . . . . . . . . . . . . . . . . 106 . . . . . . . . . . . . . . . . . . . . . . . 83 1 4 BLUE&ME™ User’s Manual 䡵 Quick Tips – Frequently Asked Questions . . . . 108 ▫ BLUE&ME™ Media Player – Quick Tips . . . . 110 ▫ What Can I Do With My BLUE&ME™ Hands-Free Communication Package? . . . . . . 108 ▫ BLUE&ME™ Message Reader – Quick Tips . . . 111 ▫ BLUE&ME™ Hands-Free Communication – Quick Tips . . . . . . . . . . . . . . . . . . . . . . . . . 108 ▫ BLUE&ME™ And The Tomtom PND (Portable Navigation Device) (If Equipped) – Quick Tips . . . . . . . . . . . . . . . . . . . . . . . . . 112 BLUE&ME™ User’s Manual 5 OVERVIEW FIAT’s Windows Mobile™ based BLUE&ME™ HandsFree Communication is a personal telematics system that incorporates communication and entertainment applications that are expressly designed for use in your car. to recognize your voice. The system is “speaker independent” and performs equally well for different users. The BLUE&ME™ Hands-Free Communication package features integrated voice recognition, steering wheel controls and a multifunction electronic display that allows you to use your Bluetooth威 wireless technology enabled mobile phone without having to take your eyes off the road. You can even keep your phone in a pocket or a bag. You are not required to train the voice recognition system 2. This device must accept all interference received, including interference that may cause undesired operation With this system, you can also play your favorite music stored on a USB stick or iPod威 and select tracks and playback modes with both voice commands or buttons The BLUE&ME™ Hands-Free Communication package on the steering wheel. installed in your car is equipped with integral hands-free This device complies with Part 15 of the FCC rules kit, message reader, and media player. BLUE&ME™ is subject to the following two conditions: designed to support the future installation of additional 1. This device may not cause harmful interference. services. The BLUE&ME™ Hands-Free Communication Package The basic characteristic of this hands-free package is voice recognition with Bluetooth威 wireless technology. With this system you can make and receive calls safely 1 6 BLUE&ME™ User’s Manual and securely using either voice commands or buttons on the steering wheel, under any driving condition, without having to take your eyes off the road or removing your hands from the steering wheel, as required by current legal regulations. For further details on the mobile phones supported by BLUE&ME™, refer to BLUE&ME™ SUPPORTED MOBILE PHONES. To get started with BLUE&ME™ Hands-Free Communication with voice recognition, you have to simply pair Bluetooth威 wireless technology enables wireless connec- your Bluetooth威 wireless technology enabled mobile tion between your mobile phone and the hands-free phone with the system. package installed on your car. Pairing is an operation that has to be performed only To use the hands-free package, you need a Bluetooth威 once. wireless technology enabled mobile phone. This handsNOTE: free package gives you the possibility of interacting • During the mobile phone pairing procedure, vocally with your mobile phone while driving, even if BLUE&ME™ attempts to detect a phone equipped your mobile device does not feature this capability. You with Bluetooth威 wireless technology within range and can also interact with your mobile phone manually and then establishes the connection using a Personal Idenvisually using the steering wheel controls and the instrutification Number (PIN). ment panel multifunction display. BLUE&ME™ User’s Manual 7 • Once your phone is paired, you have the option to transfer your mobile phone contacts to the hands-free package, to make a phone call either by using the contacts list or directly pronouncing the phone number, to answer a call, and also answer a second incoming phone call. phone functions (LAST CALLS and PHONEBOOK) and the media player. To activate settings when travelling you can only use voice commands. The hands-free package enables the following operations: • Contact calling by voice – you can call a contact in your mobile phone phonebook using your voice. You • To interact with BLUE&ME™ you can use either can also call a contact in your phonebook by scanning buttons on the steering wheel or voice commands. through the entries on the multifunction display. With voice recognition, you can perform system functions by speaking voice commands, also identified as (To use this option you have to transfer your mobile “keywords.” When the system recognizes a keyword, phone contacts to the hands-free package phonebook). it will respond with the appropriate action. Voice • Digit dialing by voice – you can dial a phone number recognition is an easy and convenient way to use by pressing the Windows icon button (VR button) on BLUE&ME™. the steering wheel and speaking the digits to be dialed. All the system functions are available within the • To call a SMS text sender – call the last SMS text BLUE&ME™ Main Menu. When you are travelling, you sender directly or the sender of an SMS message can interact with BLUE&ME™ using buttons on the received and stored in the BLUE&ME™ inbox. steering wheel or voice commands relevant only to 1 8 BLUE&ME™ User’s Manual • To answer a call – you can answer an incoming call by With your mobile phone in the vehicle and the pairing pressing the MAIN/Phone button on the steering procedure complete, connect to your mobile phone to BLUE&ME™ and you can make phone calls by speaking wheel. keywords or pressing buttons on the steering wheel. • Conference call – you can call another contact while When using the hands-free phone, the audio output of a you are engaged in a phone conversation (Conference phone conversation is heard through your car’s speakers. Calling is only supported by a compatible mobile Message Reader phone). The BLUE&ME™ message reader enables automatic • Call waiting – while engaged in a phone conversation, reading, through the car sound system, of the SMS texts you can receive notification of another incoming you receive on your Bluetooth威 wireless technology phone call, answer the other incoming phone call, and enabled mobile phone that are received when the phone switch between two ongoing phone conversations. is paired and connected to BLUE&ME™ system. The (Call waiting is only supported by a compatible momessage reader does not provide access to messages that bile phone.) were received before you entered the car and connected • Refusing an incoming call or ending a call – you can with the BLUE&ME™ system. Only a subset of abbrerefuse an incoming call or end a current call by viations and emoticons are supported by the pressing the Phone Hang-up button on the steering BLUE&ME™ system. wheel. BLUE&ME™ User’s Manual 9 NOTE: Not all mobile phones support the SMS text • To manage the list of SMS texts received on your message reader function or automatic phonebook transBLUE&ME™ paired mobile phone. fer via Bluetooth威. Consult www.fiatusa.com for further NOTE: Only messages that were received while the information on the list of compatible mobile phones. mobile phone was connected to BLUE&ME™ will be Message reader functions are managed by the control listed. buttons on the steering wheel or by the BLUE&ME™ • To read the messages received and stored. Messages voice commands. can be read multiple times. The BLUE&ME™ message reader enables the following • To call the SMS text sender using the buttons on the operations: steering wheel or voice commands. • To display on the instrument panel multifunction • To delete individual messages or the entire inbox display a visual notification signal indicating that you using the buttons on the steering wheel or voice have received a new SMS text on your Bluetooth威 commands. wireless technology enabled mobile phone, with sender’s number/name; BLUE&ME™ will also ask NOTE: Messages are to only be deleted by the whether to read you the message that has been re- BLUE&ME™ system and not by your mobile phone. ceived. 1 10 BLUE&ME™ User’s Manual The BLUE&ME™ system can also recognize and read • Audio file selection by category - you can play all abbreviations, if any (e.g., “ILUVU” will be read “I love audio files of a certain category, e.g., album, artist or you”) and can interpret most common emoticons (e.g., :-) genre. will be read “Smile”), used today to write SMS texts. NOTE: Each audio file category must be tagged before Media Player connecting to the BLUE&ME™ system. If no category is With the BLUE&ME™ media player you can play, via the tagged, the BLUE&ME™ system will index the song by car sound system, digital audio files stored on a USB stick the song title. or iPod威 by simply connecting it to the USB port located • Playback options - while playing tracks you can select in the glove box of the car. the following options: Play, Stop, Next track, Previous track, Shuffle and Repeat. With this feature, you can play your favorite personal music collections while you drive. NOTE: • iPod威 player - refer to MEDIA PLAYER FUNCTIONS. • The media player does not support audio files compressed with other formats and DRM (Digital Right The media player feature allows the following operaManagement) protected audio files. Non-supported tions: audio files that may be present on the USB device will • Digital audio playback - you can play all your digital be ignored. audio files (.mp3,.wma,.wav,.aac) or play a customized playlist (.m3u or.wpl format). BLUE&ME™ User’s Manual 11 • To use the media player, you have to simply connect Road Safety (directly or by an extension lead) your USB stick or WARNING! iPod威 to the car USB port. When the ignition key is turned to ON, BLUE&ME™ will start building your • Operating certain parts of this system while drivmedia library. At the end of this operation you can surf ing can distract your attention away from the road, the whole library and scroll its categories as desired and possibly cause an accident or other serious using the buttons on the steering wheel or voice consequences; for this reason certain functions are commands. BLUE&ME™ will then play your selecdisabled by the BLUE&ME™ system until driving tion via the car sound system. conditions are secure and, if required, only when the car is stopped. • Read and Follow Instructions: before using your system, read and follow all instructions and safety information provided in this end user manual (“User’s Manual”). Failing to follow precautions found in this User’s Manual can lead to an accident or other serious consequences. (Continued) 1 12 BLUE&ME™ User’s Manual WARNING! (Continued) WARNING! (Continued) • Keep User’s Manual in the car: when kept in the car, the User’s Manual will be a ready reference for you and other users unfamiliar with the system. Please make certain that before using the system for the first time, all persons have access to the User’s Manual and read its instructions and safety information carefully. • Do not change system settings or enter data nonverbally (using your hands) while driving. Stop the car in a safe and legal manner before attempting these operations. This is important, since while setting up or changing some functions you might be required to distract your attention away from the road and remove your hands from the wheel. General Operation • Voice Command Control: some functions within the system may be accomplished using only voice commands. Using voice commands while driving allows you to operate the system without removing your hands from the wheel. • Prolonged Views of Screen: do not access any function requiring a prolonged view of the screen while you are driving. Pull over in a safe and legal manner before attempting to access a function of the system requiring prolonged attention. Even occasional short scans to the screen may be hazardous if your attention has been diverted away from your driving task at a critical time. (Continued) (Continued) BLUE&ME™ User’s Manual 13 WARNING! (Continued) • Volume Setting: do not raise the volume excessively. Keep the volume at a level where you can still hear outside traffic and emergency signals while driving. Driving while unable to hear these sounds could cause an accident. • Use of Speech Recognition Functions: speech recognition software is inherently a statistical process which is subject to errors. It is your responsibility to monitor any speech recognition functions included in the system and address any errors. • Distraction Hazard: many features may require manual (non-verbal) setup. Attempting to perform such set-up or entering data while driving can seriously distract your attention and could cause an accident or other serious consequences. Stop the vehicle in a safe and legal manner before attempting these operations. DISPLAY AND BUTTONS ON THE STEERING WHEEL Display Multifunctional Display NOTE: In this User’s Guide, the descriptions of the menu entries refer to the multifunctional display, which visualizes some entries in abbreviated form. 1 14 BLUE&ME™ User’s Manual Front Steering Wheel Buttons 1 – MUTE/ESC 2 – PHONE/MAIN 3 – PHONE HANG UP 4 – VOICE RECOGNITION (VR) Rear Steering Wheel Buttons The right-hand control is a rocker type switch with a pushbutton in the center. Press the switch up for Volume +. Press the switch down for Volume –. The button in the center is the SRC button used to change audio sources (e.g., AM, FM, CD, Media Player). BLUE&ME™ User’s Manual 15 The left-hand control is also a rocker type switch with a pushbutton in the center. Press the top of the switch to . Press the bottom of the switch to Scan Scan Up Down . The button in the center is the PRESET UP/OK button. 1 16 BLUE&ME™ User’s Manual Button /MAIN /ESC Short press function (less than 1 second) Long press function (more than 1 second) – • Launch BLUE&ME™ Main Menu • Dial the number displayed on the display that was accessed haptically from the phonebook or the recent calls list • Accept an incoming phone call • Switch between two ongoing phone conversations (call waiting) • Dial the name/number on the display that was selected/ entered by voice recognition • Cancel voice recognition – • Cancel a voice announcement • Interrupt message reading • Exit BLUE&ME™ Main Menu • Exit the sub-menu and return to the previous menu option • Exit current menu option without storing settings • Turn the microphone on/off during a phone conversation • Mute the ring tone of an incoming call • Media player Pause on/off BLUE&ME™ User’s Manual 17 Button Short press function (less than 1 second) VOICE RECOG- • Activate voice recognition • Interrupt voice announcement to provide a new voice comNITION (VR) mand PHONE HANG UP • Reject an incoming call and end a phone call in progress • End an active call and switch to a call waiting (on hold) PRESET UP/OK (left • Confirm manually selected menu option side back of steering • Switch phone conversation from the hands-free phone to wheel) your mobile phone and vice versa • Select displayed message SCAN UP /SCAN • Scroll BLUE&ME™ menu items (left side • Scroll though media player tracks DOWN back of steering wheel • Scroll inbox messages Long press function (more than 1 second) • Repeat the last utterance in a voice interaction – – – NOTE: • When connecting to BLUE&ME™ Hands-Free Communication for the first time, your phone’s phonebook • For both operating modes of Voice Command steering wheel buttons (short or long press), the function will automatically be downloaded. If this operation is not allowed immediately after pairing for the first chosen will be activated when you release the button. time, the BLUE&ME™ system will prompt you for the 1 18 BLUE&ME™ User’s Manual phonebook each time you connect to the system. For phones containing a SIM card, the phonebook on the SIM card will be downloaded if it is allowed. See your phone’s Operating Manual for further details. Prepare Your Mobile Phone Phonebook Before creating a pairing relationship between your mobile phone and BLUE&ME™ Hands-Free Communication, you should make sure that you have contact entries in your mobile phone phonebook so that you can use them with the hands-free phone. BLUE&ME™ HANDS-FREE COMMUNICATION PACKAGE QUICK REFERENCE GUIDE To quickly get started with using the BLUE&ME™ If your phonebook is empty, quickly create several new Hands-Free Communication Package with voice recogni- entries for frequently dialed phone numbers. For further details, consult your mobile phone owner’s manual. tion and Bluetooth威 wireless technology: • Turn the ignition key to ON To properly enter contacts in your mobile phone phonebook, refer to SETTING FUNCTIONS - PAIRING YOUR MOBILE PHONE. • Try out the voice commands Important Notes • Prepare your mobile phone phonebook • Pair your mobile phone • Make a phone call Instructions for each of the above functions are given in the following paragraphs. • The phonebook copied to BLUE&ME™ can only be used when the corresponding mobile phone is paired and connected. BLUE&ME™ User’s Manual 19 • Once a mobile phone is paired to the BLUE&ME™ To try out the “Help” function, proceed as follows: system, the phone will automatically connect • Press the steering wheel button. /disconnect to the BLUE&ME™ system whenever the ignition is turned to ON/OFF. All of the BLUE&ME™ • After BLUE&ME™ says “Say a command” and plays features are fully functional when the phone is cona tone indicating that voice recognition is active, say nected to BLUE&ME™. “Help”. BLUE&ME™ will speak the list of voice commands available. NOTE: Some mobile phones may require you to accept the BLUE&ME™ connection, depending on the mobile • After the general help message is finished, say “Setphone settings. tings” and then “Help”. BLUE&ME™ will speak the list of voice commands available for the Settings • Entries stored in SIM card or mobile phone memory menu. can be transferred to BLUE&ME™ with different procedures, according to your mobile phone model. • You can then say or pronounce one of the available commands and proceed with the dialogue as you like. Try Out the Voice Commands At each stage of your dialogue with the system, you can • If you need additional help, press the always use the voice command “Help”, to get detailed wheel button and say “Help” again. indications about the voice commands available. steering 1 20 BLUE&ME™ User’s Manual Pair Your Mobile Phone CAUTION! BLUE&ME™ Hands-Free Communication only allows this operation to be performed when the car is stopped. • On your mobile phone, search for devices equipped with Bluetooth威 wireless technology (the setting on your mobile phone might be called Discover or New Device). In this list you will find BLUE&ME™ (name identifying the BLUE&ME™ system on your car); select it. • When prompted by the mobile phone, enter the PIN number shown on the instrument panel display using your mobile phone keypad. If pairing is successful, the • Press the steering wheel button and say “Setsystem will say “Connecting” and at the end the tings” then, at the end of the BLUE&ME™ message display will show a confirmation message, the ID of say “Pairing”. the paired mobile phone. • The system will show the phone pairing PIN number It is essential to wait until you see this confirmation on the multifunction display. For the next two steps, message on the display. Pressing the /MAIN button consult your mobile phone owner’s manual about on the steering wheel or /ESC before the message is Bluetooth威 pairing procedures for your phone. displayed may cancel the pairing process. If the pairing process fails, an error message will be displayed: in this event repeat the pairing procedure. To pair your mobile phone, proceed as follows: BLUE&ME™ User’s Manual 21 • After the first pairing, BLUE&ME™ will say “Welcome” immediately after connecting. This message will no longer be heard when your phone automatically connects to the BLUE&ME™ system on future ignition cycles. • BLUE&ME™ will ask if you would like to copy your paired phone phonebook to BLUE&ME™. It is recommended to copy it. To start copying the phonebook say “Yes”, otherwise say “No”. If there is just one phone number for John Smith in your phonebook, the system will ask if you would like to call John Smith. To start the call say “Yes”, otherwise say “No”. If John Smith has several phone numbers, the system will ask which phone number you would like to call (e.g., “Call John Smith (at) Work or (at) Home?” ). Answer with the type of required phone number (e.g., “(at) Home” ). If John Smith has several phone numbers but the “locaMaking a Phone Call Assume that “John Smith” is one of the contacts stored in tion” (e.g., the type of phone number like work, home, etc.) is missing, the system will display the selected your phonebook. contact and a list of related phone numbers on the To call John Smith, proceed as follows: instrument cluster display. The hands-free communication system will ask if you would like to call the phone • Press the button and say “Call John Smith”. number displayed. To respond with “yes”, say “Yes” , • If the name is recognized, the system will display the otherwise say “No”. You can also scroll through the recognized contact’s information on the display phone number list manually by pressing the buttons on screen. 1 22 BLUE&ME™ User’s Manual the back of the steering wheel until you find the required • Say “No” or press the /ESC button on the steering number. Then, press the PRESET UP/OK button on the wheel; the system will store the message so you can rear of the steering wheel to start the call. read it later. • To end the phone call, press the PHONE HANG UP button on the steering wheel. For further details on the message reader SMS, refer to the section “MESSAGE READER FUNCTIONS”. NOTE: If you encounter difficulties with any of the voice NOTE: If you encounter difficulties with any of the recognition operations, refer to HANDS-FREE COMMU- message reader settings, refer to MESSAGE READER – NICATION PACKAGE - TROUBLESHOOTING. TROUBLESHOOTING. MESSAGE READER QUICK REFERENCE GUIDE If your Bluetooth威 wireless technology enabled mobile phone supports the message reader function, at the arrival of a new SMS text, BLUE&ME™ plays a tone and it will ask if you would like to read it. MEDIA PLAYER QUICK REFERENCE GUIDE To start playing the digital audio files stored on your USB stick or iPod威, proceed as follows: • Copy tracks to your USB stick (BLUE&ME™ recognizes.wma,.mp3.wav and aac formats for audio • Say “Yes” or press the /MAIN button on the files and.wpl and.m3u formats for playlists). steering wheel or the PRESET UP/OK button on the • USB sticks without USB wire: just connect the USB rear of the steering wheel to read the last message stick (directly or by an extension lead) to the USB port received. in the glove box of the car. BLUE&ME™ User’s Manual 23 • USB sticks with USB wire: use the wire to connect the the track data, so the next time the device is connected it will perform a quick scan of the contents and be ready to USB stick to the USB port on the car. use much faster. • Turn the ignition key to ON. BLUE&ME™ will automatically start to play your digital tracks, selecting • iPod威 player - refer to MEDIA PLAYER FUNCTIONS. them from the library that was built when the USB • The set up menu also allows you to decide whether to stick was connected. play audio files automatically when connecting the • After BLUE&ME™ has built the library containing USB device, or to play them upon your command. your digital audio files, you can select and play tracks, For further details on the media player, refer to MEDIA albums, artists and playlists by interacting manually PLAYER FUNCTIONS. or verbally with BLUE&ME™. Building the library may require a few minutes if your USB stick contains NOTE: If you encounter difficulties with any of the several files. voice recognition operations, consult the section MEDIA PLAYER - TROUBLESHOOTING. NOTE: Depending on the number of files, the BLUE&ME™ system may take up to 20 minutes to fully index the files when the device is first connected to BLUE&ME™. The BLUE&ME™ system will remember 1 24 BLUE&ME™ User’s Manual HOW TO USE BLUE&ME™ HANDS-FREE COMMUNICATION Voice Commands Voice commands can be said by the driver, who does not need to change his/her normal driving position to be Steering Wheel Controls heard by the system, since the microphone is properly Buttons on the steering wheel are used to perform located and oriented to this purpose. functions on the hands-free communication package, activating voice recognition, using the media player Voice commands, which are words recognized by the functions, or selecting a BLUE&ME™ menu option. system, are identified as “keywords”. Certain buttons have multiple functions which depend The hands-free communication system recognizes and on the current state of the system. responds to a preset list of voice commands. The list of available voice commands depends on the keyword The function chosen in response to a key press is in some menu level that you are currently on. The current list is cases controlled by the duration of the key press (short or steering wheel always available by pressing the long). button and saying “Help” or, saying “Help” when NOTE: BLUE&ME™ is waiting for a voice command. • For further information refer to DISPLAY AND BUT- BLUE&ME™ also recognizes personalized versions of TONS ON THE STEERING WHEEL. voice commands, like the name of a contact in your • Instructions concerning manual controls are identified phonebook. in the text by the appropriate symbol. BLUE&ME™ User’s Manual 25 There is no voice training required for using voice If the user says a valid 1st level keyword, then the submenu relevant to that command will remain active commands with this system. until a keyword leading to another level is given, the To issue a voice command to the system, press the interaction is interrupted or the system times out because steering wheel button and wait for the radio to mute, no command has been given; the same rule applies for then listen for “Say a command” and then a tone indithe other lower levels (2nd and 3rd level). cating that voice recognition is active. Then, speak the command in your natural voice at a moderate pace. NOTE: For the list of available keywords, refer to When the system recognizes the command, it will ac- VOICE COMMANDS (KEYWORDS) - SUMMARY. knowledge your command by speaking a response or * Valid means that the keyword said is included in the acting on your command. BLUE&ME™ “dictionary” and can therefore be recogVoice commands are organized according to three in- nized by the system for the concerned level. creasing levels: 1st level, 2nd level and 3rd level. To repeat the last system voice announcement, press the steering wheel button and say “Repeat” or hold When a valid* 1st level keyword is said, the system will steering wheel down for longer than 1 second. activate 2nd level keywords; when a valid 2nd level the keyword is said, the system will activate 3rd level The system can issue voice announcements. A voice keywords. announcement is a spoken message initiated by the system. To cancel a voice announcement, press the 1 26 BLUE&ME™ User’s Manual /ESC to cancel the entire VR session or press the of currently available commands and decide on which steering wheel button, wait for the beep and say command you’d like to issue to the system. “Cancel”. Adjust the volume of phone calls to a level that is A voice interaction is a two-way communication/spoken comfortable and safe while the car is in motion. To adjust exchange between system and user. To initiate a voice the default volume of BLUE&ME™ , refer to EXTERNAL steering wheel button and AUDIO VOL function in the Owner’s Manual on the interaction, press the issue a command. To interrupt a voice announcement DVD. To temporarily adjust the volume of the current from BLUE&ME™ and say your reply before listening to phone call, press + or – or adjust the position of the radio steering knob. After the phone call is disconnected, the volume the entire voice announcement, press the wheel button and speak your command after the prompt. will revert back to the original level. /ESC but- You can press Vol + or Vol – buttons on the rear of the To stop an ongoing interaction, press the steering wheel also to adjust the volume of the current ton. You will hear a tone indicating when voice recogniBLUE&ME™ voice announcement. tion is deactivated. The hands-free communication Help option can speak Please remember that to interrupt a voice announcement, steering wheel button at you can always press the the list of commands available to you at any time, any time during a voice interaction and give a new voice depending on the keyword level that you are currently command. on. To use the Help system, say “Help”. Listen to the list BLUE&ME™ User’s Manual 27 NOTE: • After you press the steering wheel button, if you do not issue a voice command within a few seconds, the system will prompt you to say a voice command. If you do not respond after two or three prompts to enter a command, the voice recognition session will end. It is the same case with not responding to a question during a voice interaction. You will hear a tone indicating when voice recognition is deactivated. Using Voice Recognition The voice recognition system may occasionally misrecognize a voice command. To ensure that your voice commands are always recognized by the system, use the following guidelines: • After pressing the steering wheel button, say the voice command after the system says “Say a Command” and plays a tone indicating that voice recognition is active. • When the system fails to recognize your voice com• After the system asks a question, begin saying your mand, it will give you another opportunity to say the command. voice command again. If you are unsure of whether the voice command is appropriate for the given con- • If you want to say a command without waiting for the system to finish its announcement or question, you text, say “Help”. steering wheel button again can press the shortly to interrupt what the system is saying and say your command. • Speak at a normal volume. 1 28 BLUE&ME™ User’s Manual • Say words clearly, in your natural voice at a moderate • The display language can be changed from the instrupace, without stops. ment cluster menu, but to change the voice recognition (VR) language and announcements, contact your FIAT • If possible, try to minimize background noise in the Dealership or consult the dedicated site at www.fiacar. tusa.com website. • Ask the other passengers to keep silent while you are Display speaking voice commands to prevent misunderstandThe different BLUE&ME™ Main Menu options are dising since the system could recognize other words (in played on the instrument panel multifunction display. addition to or different from your voice command) if The display shows the following information: several people are speaking. • If your car has a convertible top, close it before using • Status information for the Bluetooth威 wireless techvoice recognition. nology enabled mobile phone (e.g., on a call). NOTE: • Indicates that BLUE&ME™ is currently con• In countries where the BLUE&ME™ version in native nected with a Bluetooth威 wireless technology enabled language is not available, voice recognition of the mobile phone. different commands and phonebook contacts could be difficult. You are therefore recommended to adopt a pronunciation/accent meeting the language available on BLUE&ME™. BLUE&ME™ User’s Manual 29 NOTE: This icon is only displayed when the phone initially connects to BLUE&ME™ and is part of the message that indicates the mobile phone’s network provider. Audio BLUE&ME™ Hands-Free Communication uses your incar audio equipment to deliver audio output (hands-free phone conversation, media player, voice announcements and tone signals). For this purpose, the current audio • NO BLUETOOTH - the connection between program is muted for the time needed. BLUE&ME™ and the mobile phone is disconnected (e.g., trying to make a call when no phone is con- You can always adjust the audio volume either through nected). the radio or the steering wheel controls. • Brief display of the name of your current mobile When the audio system is used by BLUE&ME™, the phone carrier (“- - - - - - - -” displayed if not available). radio display will show dedicated messages. • Information about message received, message sender BLUE&ME™ Hands-Free Communication phone number or name (if stored in the phonebook). Function Menu BLUE&ME™ Main Menu displays options within a • Current BLUE&ME™ information or current menu structured list. Each option (item) in the menu can be option. viewed on the instrument panel multifunction display. Available options enable activation of different functions or change the settings of your BLUE&ME™ system. 1 30 BLUE&ME™ User’s Manual The Main Menu includes the following options: • RECENT CALLS - this submenu allows you to view a list of the recent calls made or received. This list is either downloaded from your mobile phone memory, or accumulated via use of the hands-free phone, or both. dedicated inbox and to play them later, to call the message sender or to delete the messages. It is possible to select notification signals for the arrival of a new SMS text. Messages must be received while the mobile phone is connected to the BLUE&ME™ system. Messages that are already present on the mobile phone before entering the car and turning the ignition ON are not accessible • PHONEBOOK - this submenu allows you to view the phone numbers in your phonebook and to select one • MEDIA PLAYER - this submenu allows the ability to to dial. If there are a large number of entries in your scroll the digital audio tracks in the library by folder, phonebook, then the items will be contained in groups artist, genre, album or by playlist. This submenu is within alphabetical submenus indicating the contacts used to select and play tracks. For iPod威 players - refer within that group. The number of contacts within a to MEDIA PLAYER FUNCTIONS. group depends on the amount of entries in your • SETTINGS - this submenu allows you to perform phonebook. tasks such as managing your phonebook entries, cre• MESSAGE READER - This submenu enables the ate a pairing relationship, or select the SMS notificaability to read the last message received, calling the tion settings. message sender or deleting the last message received. It is possible to store up to 20 received messages in the BLUE&ME™ User’s Manual 31 Launching the Main Menu To launch the BLUE&ME™ Main Menu, press the /MAIN button on the steering wheel; you can then interact with the system using the steering wheel buttons. BLUE&ME™ HANDS-FREE COMMUNICATION FUNCTIONS BLUE&ME™ Hands-Free Communication lets you make and receive phone calls on your Bluetooth威 wireless technology enabled mobile phone using voice commands (keywords) or the steering wheel buttons. Navigating the menu options To navigate through the items in a menu, press the scan up or scan down buttons on the rear of the steering By using the voice commands, you can make calls to people in your phonebook by pronouncing their first wheel. and/or last name, or you can make phone calls to When the number of characters in a display message is numbers not stored in your phonebook by pronouncing too long for the allowable number of display characters, the digits of the phone number or calling the last message the text in the display message will be cut to fit the sender. display size. By using steering wheel buttons, you can make phone To select the option shown on the display, press the calls to people in your phonebook or call history list by PRESET UP/OK button on the rear of the steering wheel. selecting the associated item in the RECENT CALLS or To quit the selected option or to exit a submenu, press PHONEBOOK submenus. /ESC. 1 32 BLUE&ME™ User’s Manual In addition, you can use other calling features, such as responding to incoming calls, re-dial, callback, call waiting, reading a message or deleting it. 15 minutes. After 15 minutes BLUE&ME™ will sound a warning tone and will transfer the call to the mobile phone. Making a Phone Call NOTE: • If you encounter difficulties with any of the voice You can make a phone call using one of the following recognition operations, refer to HANDS-FREE COM- methods: MUNICATION PACKAGE - TROUBLESHOOTING. • Calling a contact in your phonebook • Before you can make and receive phone calls using the • Dialing a phone number using voice commands hands-free communication package, you must create a • Dialing a phone number using the mobile phone pairing relationship for your mobile phone. keypad • For further information refer to SETTING FUNC• Calling a phone number using call history (recent TIONS – PAIRING A MOBILE PHONE. calls) • To activate the hands-free communication package, the ignition key must be turned to the ON position. • Calling the sender of a received SMS message • If during a phone call you turn the ignition key to NOTE: For further information refer to FUNCTIONS STOP, you can continue your conversation through the OF SMS MESSAGES READER, paragraph SMS MEShands-free communication package for another SAGES MANAGEMENT BLUE&ME™ User’s Manual 33 Calling a contact in your phonebook It is a requirement that you create a pairing relationship and download your mobile phone phonebook to the hands-free communication system to use this dialing feature. If the contact has just one phone number, press the PRESET/OK button or the /MAIN on the steering wheel to start the call. If the contact has multiple phone numbers, use the scan up and scan down buttons on the rear of the steering To call a contact in your phonebook using manual wheel to view the different phone numbers and then interaction, proceed as follows: select the required one by pressing the PRESET UP/OK /MAIN button on the steering wheel to /MAIN button on the steering wheel to button or the Press the start the call. open the Main Menu. and Scan Down buttons on the To end the phone call, press the PHONE HANG UP Use the Scan Up button on the steering wheel. rear of the steering wheel to select PHONEBOOK and then press PRESET UP/OK button on the rear of the Or, using voice interaction: steering wheel. Assume you would like to call the contact “John Smith” To select the alphabetical grouping which your contact’s in your mobile phone phonebook. name belongs to, press the PRESET UP/OK on the rear of Press and say “Call John Smith” or “Call John Smith the steering wheel, then select the required contact. (on/at) Mobile” (in the previous statement, the keyword “Mobile” represents the type of phone number you 1 34 BLUE&ME™ User’s Manual would like to call. The phone number type can either be To call the displayed phone number, say “Call”. “(at) Home”,“(at) Work”, or “(on/at) Other”). If the contact is correct but the phone number is wrong, If the name is recognized, the system will display the you can scroll through the phone number list manually and Scan Down buttons on recognized contact’s information (John Smith, in this by pressing Scan Up the rear of the steering wheel. When you find the example) on the display screen. /MAIN button on the required number, press the If John Smith has just one phone number, the system will steering wheel to start the call. ask if you would like to call John Smith. To start the call say “Yes” , otherwise say “No”. To end the phone call, press the PHONE HANG UP button on the steering wheel. If John Smith has several phone numbers, the system will ask which phone number you would like to call (e.g., Practical hint “Call John Smith(at) Work or (at) Home?”). Answer with When you call a contact with multiple phone numbers, the type of required phone number (e.g., “(at) Home” ). use the “at location” portion of the voice command (e.g., “(at) Home”,“(at) Work”,“(on/at) Mobile”). This will If John Smith has several phone numbers but the “locashorten the number of steps required to make the phone tion” (i.e.: the type of phone number like work, home, call. etc.) is missing, the system will display the selected contact and a list of related phone numbers. BLUE&ME™ User’s Manual 35 then say the remaining digits and then say “Dial” or Dialing a phone number using voice commands To dial a phone number using voice interaction, proceed press the /MAIN button on the steering wheel to start as follows: the call. Press the steering wheel button and say “Dial”. The system will respond with “Number, please”. The system will start the call to the displayed phone number. To end the phone call, press the PHONE HANG UP Say the phone number as a sequence of single digits (e.g., button on the steering wheel. “0”, “1”, “2”, “3”, “4”, “5”, “6”, “7”, “8”, “9”, “+” (plus), You can say the sequence of phone number digits in “#” (pound) or “*” (star). “digit groups” which allows you to verify the recognized For example, 248 555 1212 has to be said as: “two, four, number in several small portions. Digit groups are creeight, five, five, five, one, two, one, two”. ated by the pauses you use while pronouncing the The system will repeat the complete phone number and sequence of digits. If you pause after pronouncing several digits, a digit group is created. The system will display it. repeat the recognized digits. If the number is complete, say “Dial” or press the /MAIN button on the steering wheel to start the call. If the spoken digits are correct, you can continue proIf you have not finished speaking the phone number, nouncing the phone number. If the spoken digits are incorrect, you can delete the digit group by saying 1 36 BLUE&ME™ User’s Manual “Delete”. The system will delete the last group of num- also recognize other voices; there is a risk that some bers and display the partially dialed phone number. numbers will be accidentally recognized, added to corThen, you can say the digit group again and also the rect numbers or not recognized. remaining phone number digits. Dialing a phone number using the mobile phone keypad To cancel the phone call, say “Cancel”. Alternatively, you can dial a phone number using your To cancel the phone call and start dialing again, say mobile phone keypad and then continue your conversa“Start over”. tion using the hands-free communication system. To ask the system to repeat the recognized phone numIt is a requirement that you create a pairing relationship ber, say “Repeat”. If no phone number was dialed, the and that the mobile phone is within range of the handssystem says “No number available”. free communication system of your car. If the repeated phone number is correct, say “Dial” to To dial a phone number using your mobile phone keystart the call. pad, proceed as follows: NOTE: When connected to BLUE&ME™ and dialing a • Dial the phone number on your mobile phone keypad phone number by voice commands, it is essential to and connect the phone call following the procedure minimize background noise in the car and to ask the required by your mobile phone. other passengers to keep silent while you are speaking the digits. Since the system is speaker independent, it can BLUE&ME™ User’s Manual 37 • Conduct the conversation using the hands-free com- • The system will present a list of phone numbers. Use munication system. the Scan up/Scan down buttons to select the required phone number. Then press the PRESET UP/OK button • To end the phone call, press the PHONE HANG UP /MAIN on the rear of the steering wheel or the button on the steering wheel, or end the phone call button on the steering wheel to start the call. from your mobile phone keypad. • To end the phone call, press the PHONE HANG UP Calling a phone number using call history (recent button on the steering wheel. calls) RECENT CALLS option is a list of the recent calls made Or, using voice interaction: or received. It can consist of up to ten incoming calls, up To call back the last incoming phone number, press the to ten outgoing calls and up to five missed calls. steering wheel button and say “Call back”. To dial a phone number using manual interaction, proThe system will display information about the last caller ceed as follows: and ask if you would like to call back this contact. To • Press the /MAIN button on the steering wheel to respond with “yes”, say “Yes”, otherwise say “No”. open the Main Menu. • Select RECENT CALLS and then press the PRESET UP/OK button on the rear of the steering wheel. 1 38 BLUE&ME™ User’s Manual To redial the last phone number you called, say “Redial”. Answering a phone call The system will display information about the last con/MAIN button • To answer the phone call, press the tact you called and will ask if you would like to redial on the steering wheel. this phone number. To redial the last phone number called, say “Yes” , otherwise say “No”. • To end the phone call, press the PHONE HANG UP button on the steering wheel. NOTE: If there are no incoming calls stored on the RECENT CALLS list, BLUE&ME™ will say “No re- Rejecting a phone call ceived calls” and the display will read “No call found”. • To reject the phone call, press the PHONE HANG UP Incoming Calls button on the steering wheel. With the hands-free communication system you can Ignoring a phone call respond to incoming phone calls using the steering wheel buttons. When a phone call is received, the system will • To ignore the phone call and mute the phone call ring display information about the caller’s identity, if avail/ESC button. Press the /ESC tone, press the able. again to hear the call or ring tone again. The incoming phone call can have a customized ring tone (if this function is available on your mobile phone). BLUE&ME™ User’s Manual 39 Answering an incoming phone call during an active phone conversation To answer an incoming phone call while another phone conversation is active, press the /MAIN button on the steering wheel. The system will switch to the incoming phone call and put the current phone conversation on hold. Managing Phone Calls Transferring a phone conversation from your mobile phone to the hands-free communication system If you enter the car during a phone conversation from your mobile phone and you want to continue the conversation using the car hands-free communication system, you can transfer the phone conversation to it. NOTE: • Not all mobile phones and carriers support this feature. Contact the FIAT Dealership or consult the Proceed as follows: www.fiatusa.com website for compatible mobile • Get into the car and turn the ignition key to ON, to phones activate the hands-free communication system. • Certain mobile phones support the ability to transmit • If the permissions on the phone are set to allow an your contact’s ring tones to the hands-free communiautomatic connection the conversation will be transcation system and play customized ring tones for ferred automatically. Otherwise the system will send a incoming phone calls. In this case, the incoming phone message to your mobile phone offering hands-free calls will have your mobile phone customized ring phone support. tones. The ring tone format must be compatible with the type of audio files that BLUE&ME™ supports. 1 40 BLUE&ME™ User’s Manual • To transfer the conversation to the hands-free phone, Muting a phone call enter the information required by your mobile phone. To mute a phone call on and disable the microphone so that you can talk without being listened to by the caller, (This process is different for each mobile phone). /ESC. press the • The phone conversation is then transferred to the system. Conference Call Function Transferring a phone conversation from the hands-free phone to your mobile phone To transfer a phone conversation from the hands-free communication system to your mobile phone, press the PRESET UP/OK button on the rear of the steering wheel. NOTE: Only with Bluetooth威 wireless technology enabled mobile phones supporting this function. With the Conference Call function you can call another contact while you are engaged in a phone conversation. In this way you can speak with both contacts at the same You can talk on your mobile phone and still use buttons time. on the steering wheel. Specifically, you can press the /MAIN button on the steering wheel to switch be- To start a conference call while you are still engaged in a phone conversation, call the second required contact as tween two phone calls on your mobile phone, or press described in MAKING A PHONE CALL. button on the steering wheel the PHONE HANG UP to end the active call and activate the call on hold. When the Conference Call option is active, the display will show “CONFERENCE”. BLUE&ME™ User’s Manual 41 If you want BLUE&ME™ to read the SMS message To end both calls, press the PHONE HANG UP button on the steering wheel. Both calls will be ended at received by manual interaction, press the PRESET UP/OK button on the rear of the steering wheel. The the same time. message will be read and any abbreviation or emoticon MESSAGE READER FUNCTIONS contained in the message will be spoken. If your mobile phone with Bluetooth威 wireless technol/ESC ; BLUE&ME™ will not ogy supports the message reader function, at the arrival Otherwise, press the read the message but it will store it so you can read the of a new SMS text, BLUE&ME™ plays a tone and it will ask if you would like to read it (according to set signal message later (for further information refer to, HOW TO READ THE LAST SMS TEXT RECEIVED). types). Even though your mobile phone is paired and connected to the BLUE&ME™ Hands-Free Communication system, you might not be able to read SMS text messages on the BLUE&ME™ system. To view the list of mobile phones and functions supported, go to the BLUE&ME™ www.fiatusa.com website or contact Customer Services at 888-CIAO-FIAT (888-242-6342). NOTE: For information on signal types, refer to SMS NOTIFICATION SETTINGS. Or, using voice interaction: If you say “Yes”,BLUE&ME™ will read the message and speak any abbreviations and emoticons in the message. Otherwise say “No” ; the system will store the message so you can read it later (for further information refer to HOW TO READ THE LAST SMS TEXT RECEIVED). 1 42 BLUE&ME™ User’s Manual messages could be lower) when your mobile phone is connected with Bluetooth威. When the inbox is full, the new incoming message will delete the oldest message received (even if not yet read). It is also possible to delete just one message or to delete the entire inbox (refer to To read the last message received, open the BLUE&ME™ MANAGING MESSAGES). Main menu and select the option MESS. READER, then press the PRESET UP/OK button on the rear of the To read a particular message stored in the inbox, open the steering wheel. Select the option READ LAST and press BLUE&ME™ Main menu and select the option MESS. the PRESET UP/OK button on the rear of the steering READER, then press the PRESET UP/OK button on the wheel; BLUE&ME™ will read the last message received. rear of the steering wheel. How To Read The Last SMS Text Received After receiving a message, BLUE&ME™ will store it (both read or not read messages) in the inbox (refer to INBOX). Select the INBOX option, then press the PRESET UP/OK button on the rear of the steering wheel. Scroll stored steering wheel button and pronounce Press the messages and select the desired one, the system will “Read last one”;BLUE&ME™ will read the text of the display the SMS text senders identification data, if availlast message received. able. Select READ and press the PRESET UP/OK button on the rear of the steering wheel; BLUE&ME™ will read Inbox BLUE&ME™ will store up to 20 received messages (in the selected message. the event of linked messages, the number of stored Or, using voice interaction: BLUE&ME™ User’s Manual 43 To access these options when reading a message, open steering wheel button and say “Message the BLUE&ME™ Main menu and then press the PREPress the SET UP/OK button on the rear of the steering wheel to reader”, after the audible tone, say “Inbox” ; select the desired option. BLUE&ME™ will display the text sender’s identification data for the first message contained in the inbox (and also Or, using voice interaction: the phone number of the SMS text sender, if stored in the Press the steering wheel button and say “Read” or phonebook). “Call” or “Delete”; the system will perform the desired To scroll the Inbox, say “Previous” or “Next” ; when the option. required message is displayed, say “Read”,BLUE&ME™ Deleting All Messages will read the selected message. BLUE&ME™ can store a maximum of 20 messages; a Say “Delete” to delete the selected message. new incoming message will delete the oldest one reManaging Messages ceived from the inbox. All messages stored by For every message received, while BLUE&ME™ is con- BLUE&ME™ can be deleted by a single command. nected to your phone, BLUE&ME™ can: To delete all messages, open the BLUE&ME™ Main 쐍 read the message menu and select DELETE ALL, then press the PRESET UP/OK button on the rear of the steering wheel. The 쐍 call the sender directly system will ask DEL. MESS.? Press the PRESET UP/OK 쐍 delete the message Or, using voice interaction: 1 44 BLUE&ME™ User’s Manual button on the rear of the steering wheel to delete all • VIS. SIGNAL:BLUE&ME™ will notify you of a new /ESC button to cancel. messages, or press the incoming message using a visual signal on the instrument panel display. The message received can also be Or, using voice interaction: read later by pressing the PRESET UP/OK button (refer to HOW TO READ THE LAST SMS TEXT steering wheel button and say “Message Press the RECEIVED AND INBOX). reader”. After the audible tone say “Delete all”;BLUE&ME™ will • READER OFF:BLUE&ME™ deactivates the Message reader; a new incoming message will not be signalled ask “Delete all messages from the vehicle now ?” say and will not be transmitted to or stored on the system. “Yes” to delete all messages, otherwise say “No”. Open the BLUE&ME™ Main menu, select the option MESS. READER , and then press the PRESET UP/OK button on the rear of the steering wheel. Select the option SIGNAL TYPE and scroll the three available options using the up and down buttons, or select the desired • VIS.+ACOUST.:BLUE&ME™ will notify you of a option and then press the PRESET UP/OK button on the new incoming message using a visual signal on the rear of the steering wheel. instrument panel display and through an audible tone. BLUE&ME™ will also ask if you would like to read the message. SMS Notification Settings With the BLUE&ME™ message reader it is possible to set three notification signals to announce the arrival of a new SMS text: BLUE&ME™ User’s Manual 45 Or, using voice interaction: MEDIA PLAYER FUNCTIONS 1 steering wheel button and say “Message Press the reader”. After the audible tone say “Signal type” ; BLUE&ME™ will list the available options and then you can select the required one by saying “Reader off” or “Visual and acoustic signal” or “Visual signal only”. 1 – USB Port 2 – Auxiliary Jack The MEDIA PLAYER menu enables the following: • to display tracks stored on your USB device/iPod • to play audio files stored on your USB device/iPod. 46 BLUE&ME™ User’s Manual NOTE: Before using the player, refer to COMPATIBLE • Turn the ignition key to ON. If the AUTOPLAY feature USB STORAGE DEVICES to check that your USB is set to ON, BLUE&ME™ will start playback automemory device is compatible with BLUE&ME™. matically when a USB device is present in the USB port. How To Connect The USB Device/iPod To • If AUTOPLAY is set to ON, BLUE&ME™ will start BLUE&ME™ Hands-Free Communication playback automatically when a USB device is inserted To connect your USB device/iPod to BLUE&ME™ into the USB port Hands-Free Communication, proceed as follows: • Copy tracks on your USB device/iPod ( BLUE&ME™ NOTE: recognizes.wma,.mp3 and.wav,.aac formats for audio • For the best use of BLUE&ME™ it is recommended to use USB devices with maximum capacity of 32 GB files and.wpl and.m3u for playlists). • USB devices without USB wire: just connect the USB device/iPod (directly or by an extension lead) to the USB port on the car. • Indexing time will increase with the number of files present on the media device. For a good customer experience, a maximum total file size of 4 GB on the media device is recommended. • USB devices with USB wire: use the wire to connect • For further information refer to SETTINGS FUNCthe USB device/iPod to the USB port on the car. TION - MEDIA PLAYER. The multimedia player does not play audio files covered • It is possible to use BLUE&ME™ to select and play by digital rights (DRM). tracks after the media library has been built. BLUE&ME™ User’s Manual 47 How To Manage The Media Library Using the media player you can select the audio files stored on your USB device/iPod, using voice commands or the steering wheel buttons. BLUE&ME™ can support media information whereas the.wav format files do not. BLUE&ME™ will populate the title field in the index with the filename as the track name for the folder option. NOTE: For the best use of BLUE&ME™ it is recom- • For further details, refer to PRACTICAL HINTS FOR USING THE MEDIA PLAYER. mended to use USB devices with maximum capacity of 32 GB. Selection by folder You can scroll audio files by folder, artist, genre, album or Track folders on your USB device/iPod are displayed in playlist and then select the desire category using voice the FOLDERS menu (not available for most iPods). commands. After selecting the desired category, select the To select tracks through manual interaction, proceed as desired file using the manual controls. follows: To surf your media library use the track data (e.g., title, /MAIN button to launch the Main Menu Press the artist, album, genre). USB sticks can also be surfed in and select MEDIA PLAYER, then select USB OPTIONS folders mode. and press the PRESET UP/OK button on the rear of the NOTE: steering wheel. • Not all formats can support media information. The.mp3 and.wma,.aac recognized formats by Select FOLDERS , then press the PRESET UP/OK button. 1 48 BLUE&ME™ User’s Manual Use the Scan Up/Scan Down buttons to scroll through the folders. To play all song tracks in all folders, select PLAY ALL and then press the PRESET UP/OK button. To display folder tracks, select the desired folder and press the PRESET UP/OK button. Scroll the selected folder tracks. To play a desired track, select the title and then press the PRESET UP/OK button on the rear of the steering wheel. NOTE: For further details on FOLDERS, or menu customization, refer to PRACTICAL HINTS FOR USING Scroll the selected folder tracks. To play a desired track, THE MEDIA PLAYER. select the title and then press the PRESET UP/OK button Selection by artist on the rear of the steering wheel. To select a specific artist’s song tracks, proceed as follows: Or, by using voice interaction: /MAIN button to launch the Main Menu Press the steering wheel button and say “Media and select MEDIA PLAYER, and then select USB OPPress the Player”, then, after the beep, say “Advanced USB op- TIONS and press the PRESET UP/OK button on the rear of the steering wheel. tions” and finally, after the beep, say “Folders”. Use the Scan Up/Scan Down buttons to scroll through Select ARTISTS and then press the PRESET UP/OK the folders. To play all song tracks in all folders, select button. PLAY ALL and then press the PRESET UP/OK button. To Use the Scan Up/Scan Down buttons to scroll through display folder tracks, press the PRESET UP/OK button. the Artists. To play music from a desired artist, select the artist and press the PRESET UP/OK button. BLUE&ME™ User’s Manual 49 Or, by using voice interaction: To play a track by a selected artist, select the title and then press the PRESET UP/OK button. steering wheel button and say “Media Press the Player”, then, after the beep, say “Advanced USB op- NOTE: If your USB device/iPod contains many audio files, the ARTISTS menu will be subdivided into alphations” and finally, after the beep, say “Artists”. betical submenus. The alphabetical submenu will display Use the Scan Up/Scan Down buttons to scroll the artist’s just the first letter of the artists it contains (e.g., A-F), or it albums. To play all the albums of a desired artist, select will display the first two letters (e.g., Aa-Ar). PLAY ALL and press the PRESET UP/OK button. Selection by genre To play an album by the selected artist, select the desired To select the tracks by genre using manual interaction, album and then press the PRESET UP/OK button. proceed as follows: To play a track by the selected artist, select the title and Press the /MAIN button to launch the Main Menu then press the PRESET UP/OK button. and select MEDIA PLAYER, then select USB OPTIONS Use the Scan Up/Scan Down buttons to scroll the artist’s and press the PRESET UP/OK button on the rear of the albums. To play all the albums of the desired artist, select steering wheel. PLAY ALL and then press the PRESET UP/OK button. To Select GENRES and then press the PRESET UP/OK play an album by a selected artist, select the desired button. album and then press the PRESET UP/OK button. 1 50 BLUE&ME™ User’s Manual Or, by using voice interaction: Selection by album To select an album using manual interaction, proceed as steering wheel button and say “Media Press the follows: Player”, then, after the beep, say “Advanced USB op/MAIN button to launch the Main Menu Press the tions” and finally, after the beep, say “Genre”. and select MEDIA PLAYER, then select USB OPTIONS Use the Scan Up/Scan Down buttons to scroll the genres. and press the PRESET UP/OK button on the rear of the To play all the tracks of the selected genre, press the steering wheel. PRESET UP/OK button. Select ALBUMS and then press the PRESET UP/OK NOTE: If your USB device/iPod contains many audio button. files, the GENRES menu will be subdivided into alphabetical submenus. The alphabetical submenu will display Use the Scan Up/Scan Down buttons to scroll through just the first letter of the name of genre it contains (e.g., the albums. To play music from a desired album, select A-F), or it will display the first two letters (e.g., Aa- Ar). the album and press the PRESET UP/OK button. Use the Scan Up/Scan Down buttons to scroll through the album tracks. To play all the tracks in the album, select PLAY ALL and press the PRESET UP/OK button. To play just one track, select the track title and press the PRESET UP/OK button. BLUE&ME™ User’s Manual 51 Or, by using voice interaction: just the first letter of the albums it contains (e.g., A-F), or it will display the first two letters (e.g., Aa- Ar). steering wheel button and say “Media Press the Player”, then after the beep, say “Advanced USB op- Selection by playlist Playlists stored in your USB device/iPod can be distions” and finally, after the beep, say “Albums”. played with the PLAYLISTS menu. Use the Scan Up/Scan Down buttons to scroll through the albums. To play music from a desired album, select To select a playlist using manual interaction, proceed as follows: the album and press the PRESET UP/OK button. Use the Scan Up/Scan Down buttons to scroll through the album tracks. To play all the tracks in the all the albums, select PLAY ALL and press the PRESET UP/OK button. /MAIN button to launch the Main Menu Press the and select MEDIA PLAYER, then select USB OPTIONS and press the PRESET UP/OK button on the rear of the steering wheel. To play just one track, select the track title and press the Select PLAYLISTS and press the PRESET UP/OK button. PRESET UP/OK button. Use the Scan Up/Scan Down buttons to scroll the playNOTE: If your USB device/iPod contains many audio lists. To play a displayed playlist, select the playlist and files, the ALBUMS menu will be subdivided into alpha- press the PRESET UP/OK button. betical submenus. The alphabetical submenu will display 1 52 BLUE&ME™ User’s Manual Or, by using voice interaction: To start PLAY ANYTHING using manual interaction, proceed as follows: steering wheel button and say “Media Press the /MAIN button to launch the Main Menu Player”, then after the beep, say “Advanced USB op- Press the and select MEDIA PLAYER, then select USB OPTIONS tions” and finally, after the beep, say “Playlists”. and press the PRESET UP/OK button on the rear of the NOTE: For further details on how to build playlists, steering wheel. refer to PRACTICAL HINTS. Select PLAY ANYTHING and press the PRESET UP/OK Playing Audio Tracks button. NOTE: For managing audio files on iPod or iPhone Or, using voice interaction: devices, refer to TECHNOLOGIES SUPPORTED BY steering wheel button and say “Media BLUE&ME™ Hands-Free Communication, MANAG- Press the ING AUDIO FILES FROM IPOD DEVICES. Player”, then after the beep, say “Advanced USB options” and finally, after the beep, say “Play Anything”. Shuffle playback of the whole media library The option PLAY ANYTHING can be used to quickly For further details on digital audio files playback, refer to play the whole content of your media library at random. DIGITAL AUDIO SELECTION. BLUE&ME™ User’s Manual 53 Audio play Play To start playing an audio file using manual interaction, To resume playback of the paused track: Press the /ESC button, or the MUTE button on the radio. proceed as follows: If the AUTOPLAY option is on, connect your USB Stop device/iPod to BLUE&ME™ ;track playback will start To stop playing a track: press the steering wheel automatically. button and say “Stop”. To resume playback : press the steering wheel button and say “Play”. You can also select the required audio file and then press the PRESET UP/OK button on the rear of the steering Next track wheel. To play the next track using manual interaction, proceed as follows: Or, using voice interaction: Press the anything”. steering wheel button and say “Play While playing a digital track press the Scan Up steering wheel button. Pause To pause the track being played: Press the MUTE button on the radio. rear Or, using voice interaction: /ESC or the While playing a digital track, press the wheel button and say “Next”. steering 1 54 BLUE&ME™ User’s Manual NOTE: For further details on voice commands (keyPrevious Track To play the previous track using manual interaction, words) to be used with the media player, refer to VOICE COMMANDS (KEYWORDS) - SUMMARY. proceed as follows: While playing a digital track press the Scan Down rear steering wheel button. iPod威 compatibility What I can do Or, using voice interaction: • Listen to tracks in digital quality While playing a digital track, press the wheel button and say “Previous”. steering • Select tracks by category (Artist, Album, Genre, etc.) by voice control or using the controls on the steering wheel NOTE: If the “Previous” track (manual or voice) com- • Recharge the iPod威 via USB mand is given after playing the first 3 seconds of the track, the track will be started over. If it is given within NOTE: • The device must be in playback mode or paused to the first 3 seconds, the previous track will be played. start playing a track on some iPod威/iPhone models. Changing audio sources To change the current sound source (Radio, CD, CD • Load the tracks onto the iPod威/iPhone device using the procedure specified in the device manual. Changer, Media player), press the PRESET UP/OK button on the rear of the steering wheel or FM, AM or • It is advisable to keep telephones and iPod威s updated MEDIA buttons on the radio. for optimal operation with the BLUE&ME™ system. BLUE&ME™ User’s Manual 55 What I cannot do • Play audio tracks in m4p, and mp4 formats multimedia files must be present and up to date. To update file data, follow the instructions given in your media file management software instruction manual. • Play audio tracks purchased on digitally protected • If certain items in your library have no Artist, Album, tracks (DRM) (only on certain iPod威 devices and USB Title and Genre, BLUE&ME™ will show UNKNOWN sticks) in ALBUMS and GENRES menus. To enter the rePractical Hints For Using The Media Player quired data, follow the instructions given on your software instruction manual. Scrolling Building the media library on BLUE&ME™ • To optimize scrolling of the FOLDERS menu, organize Hands-Free Communication folders on your USB stick before connecting it to BLUE&ME™. To facilitate and to optimize FOLDERS • Building the media library may require a few minutes. If the time required is excessive, you can intervene by menu selection, organize your tracks in folders with reducing the number of audio files stored on your USB names that mean something to you. device/iPod威. Organize media files • While building the library, it is possible to play a • In order to make the musical selection on random track selection. BLUE&ME™ will build the BLUE&ME™ based on predefined selection criteria library while playing music. (author, album, type, etc.), information contained in 1 56 BLUE&ME™ User’s Manual Building playlists for BLUE&ME™ Hands-Free • Click on Save. Communication When the above steps are complete, the new file.m3u For building.m3u or.wpl playlist for BLUE&ME™ using or.wpl will be built. Microsoft威 Windows Media威 Player, proceed as follows: • Copy required tracks into a new folder or to your USB SETTING FUNCTIONS The SETTINGS menu enables you to perform the folmemory device. lowing functions: • Open Microsoft威 Windows Media威 Player. Select File • Pair a mobile phone , and then Open from the menu. • Scroll the content of the USB device/iPod威 connected • Manage user data to your computer and select the audio files to be • Change the Media player settings entered in the playlist (only available on certain iPod威 • View the Advanced options devices). NOTE: The settings submenu are only accessed by • Click on Open. using the steering wheel buttons. • Move to File and select Save Now Playing List As.... In field File Name enter the required name and in field To perform functions and adjustments in the SETTINGS menu, you may use the buttons on the steering wheel or Save as type set the type:.wpl or.m3u. voice commands while the vehicle is not moving. When BLUE&ME™ User’s Manual 57 the vehicle is moving, you can use voice commands only. NOTE: Some mobile phones may require a setting change or access permission change in order for Instructions are provided for both methods. BLUE&ME™ to automatically reconnect. See your moNOTE: If you encounter difficulties with any of the bile phones manual for more information. BLUE&ME™ settings, refer to TROUBLESHOOTING. IMPORTANT! The mobile phone pairing PIN number is Pairing a Mobile Phone a special PIN generated randomly at each new pairing Before you can use your mobile phone with the handsand used just for this operation. It is not your SIM PIN free communication function on your car, you must and therefore it is not required to store or to keep it in create a pairing relationship between the mobile phone mind; losing it will not impair the hands-free communiand the hands-free communication system. cation system operation. During the pairing procedure, the hands-free communiThe pairing procedure will only need to be performed cation system attempts to detect a Bluetooth威 wireless once for your mobile phone. After this procedure technology enabled mobile phone within range, and then BLUE&ME™ will automatically connect to your phone establishes the connection using a Personal Identification each time you get into the car and turn the ignition key to Number (PIN). After a pairing relationship is established, ON. you can use the hands-free communication system to make and receive phone calls, and do other operations You can create a pairing relationship using the PAIRING via your wirelessly-connected mobile phone. option in the SETTINGS menu. 1 58 BLUE&ME™ User’s Manual To create a pairing relationship using manual interaction, wireless technology enabled mobile phones and select BLUE&ME™ (item that identifies BLUE&ME™ on your proceed as follows: car). /MAIN button to open the Main Menu, then Press the select SETTINGS by pressing the PRESET UP/OK but- When prompted by the mobile phone, enter the PIN number shown on the instrument panel display. If pairton. ing is successful, the system will say “Connecting” and Select PAIRING and then press the PRESET UP/OK then the display will show the paired mobile phone ID. button. The system will start the pairing procedure. It is of vital importance to wait until this confirmation BLUE&ME™ will show the mobile phone pairing PIN message is displayed, since pressing the /MAIN on the instrument panel display and announces it. Please button or the /ESC button will cancel the pairing note that this is a PIN used just for this operation; it is not process. If pairing fails, an error message will be disyour SIM PIN. played and the pairing procedure needs to be repeated. For the next two steps, consult your mobile phone After pairing, the system will say “Welcome” immediowner’s manual about Bluetooth威 pairing. ately after connecting. This message will no longer be On your mobile phone, query for Bluetooth威 wireless heard the next time the phone connects to the system. technology enabled mobile phones that are within range The system will ask if you would like to copy your paired (this option on your mobile phone might be called phone’s phonebook. It is recommended to copy it. To Discover, New Device, etc.). View the list of Bluetooth威 BLUE&ME™ User’s Manual 59 start copying the phonebook, press the PRESET UP/OK /ESC button. You can button; otherwise press the download your phonebook at a later time using the menu option SETTINGS, USER DATA, or PHONEBOOK. wireless technology enabled mobile phones and select “ BLUE&ME™ ” (item that identifies the hands-free communication package in your car). On your mobile phone, query for Bluetooth威 wireless technology enabled mobile phones that are within range (this option on your mobile phone might be called Discover, New Device, etc.). View the list of Bluetooth威 The first time a phone connect to the system, the system will say “Welcome” immediately after connecting. This message will no longer be heard the next time the phone connects to the system. When prompted by the mobile phone, enter the PIN number shown on the instrument panel display using your mobile phone keypad. If pairing is successful, the Or, using voice interaction: system will say “Connecting” and then the display will button and say “Settings”, wait for the show the paired mobile phone ID. Press the tone then say “Pairing”. It is of vital importance to wait until this confirmation The system shows the mobile phone pairing PIN on the message is displayed, since pressing the /MAIN or instrument panel display and repeats it. /ESC buttons at this time may cancel the pairing For the next two steps, consult your mobile phone process. If pairing fails, an error message will be displayed and the pairing procedure needs to be repeated. owner’s manual about Bluetooth威 pairing. 1 60 BLUE&ME™ User’s Manual The system will ask if you would like to copy your phone’s phonebook. Copying is recommended. To start copying the phonebook, say “Yes”; otherwise say “No”. enter “Tanja” as “Tanya”, to improve recognition accuracy and also to obtain the correct pronunciation by the system. For certain mobile phones the phonebook is not copied • When adding or editing contact entries, insert the appropriate accent marks when the name requires automatically, in this case you must send the contacts in these marks to be properly pronounced and recogyour mobile phone’s phonebook to the BLUE&ME™ nized by the system. For example enter “Nicolo Rehands-free communication system using your mobile bora” as “Nicolò Rébora” to obtain the correct pronunphone keypad. ciation. Practical hints To improve both the voice recognition of your phone- • When adding or editing contact entries, bear in mind book entries and BLUE&ME™ pronunciation accuracy that certain capital letters may be read as Roman when repeating the entries, please try to enter contact numerals (e.g., V may be read as fifth). entries and memorize them using the following criteria: • When calling contacts by voice, do not include the • Avoid abbreviations. middle names or middle initials of your contacts. • Write foreign names according to the way in which they are pronounced according to the rules of the BLUE&ME™ language set on your car. For example, BLUE&ME™ User’s Manual 61 NOTE: • Depending on the size of your phonebook, • You only need to pair your mobile phone a single time. BLUE&ME™ may take some time to download or check for updates. So, if you try to immediately make • You can pair up to five mobile phones, but only one a phone call after getting into the vehicle, the phone can be used at a time. To use one of the other BLUE&ME™ system may tell you to wait. paired phones, the currently connected phone needs to be powered off or it’s Bluetooth威 setting must be • The system will download only valid contact entries. A valid contact entry must include both a name and at turned off. BLUE&ME™ will then search the paired least one phone number. phone list looking for a phone to connect to. • On your paired mobile phone, the Bluetooth威 setting • If you would like to re-pair your mobile phone, delete must be turned on in order to connect your mobile the old pairing relationship first. During this operation phone with BLUE&ME™ Hands-Free Communicaall paired phones and their associated phonebook tion. information will be deleted. To delete a paired phone from the system, from the USER DATA menu, select • Before transferring your mobile phone contacts to the DELETE USERS. On your mobile phone, delete hands-free communication system, make sure that BLUE&ME™ from the list of Bluetooth威 mobile each contacts first and last name is unique and disphones following the specific instructions for your tinctly recognizable to improve the voice recognition mobile phone (refer to your mobile phone owner’s results. manual). 1 62 BLUE&ME™ User’s Manual • If you download a phonebook with a contacts list including more than 1000 contacts, the system may operate slower than expected and voice recognition of the names in your phonebook may be degraded. BLUE&ME™. Not all phones support phonebook downloading or copying individual contacts. Consult www.fiatusa.com for further information on the list of compatible mobile phones. • If the pairing list is accidentally deleted, the pairing To open the USER DATA menu using manual interaction, proceed as follows: procedure will be repeated. Managing User Data You can manage the user data used by BLUE&ME™ by entering the USER DATA menu. The phonebook can be deleted, all paired phones and their associated phonebook data can be deleted, or all data can be deleted. If all data is deleted then the memory in BLUE&ME™ will be restored to it’s initial empty condition. If the phonebook had not been previously downloads during the phone’s initial pairing then you can choose to download it now or you can copy individual contacts from you phone to Press the /MAIN button to open the Main Menu, then select SETTINGS by pressing the PRESET UP/OK button. Select the USER DATA and then press the PRESET UP/OK button. Or, using voice interaction: button and say “Settings”. Wait until Press the after the tone then say “User data”. In the USER DATA menu you can perform the following functions described below. BLUE&ME™ User’s Manual 63 Delete user data In the USER DATA menu you can delete the pairing list. After you delete the pairing list, you cannot use an unpaired phone with the hands-free communication system, or its phonebook, until you re-pair it. Always remember that this operation deletes all the devices from the pairing list. The system will ask “Delete all paired users?”. To confirm, say “Yes”. NOTE: • Always remember that if a mobile phone is paired with the system while another phone is connected, the connection with the current phone is ended to establish a connection with the new phone. To delete user data using manual interaction, proceed as • It is not possible to delete the pairing relationship with follows: a single phone on the pairing list unless it is the only phone present on the pairing list. Select DELETE USERS and then press the PRESET UP/OK button. • If all paired users are deleted from the pairing list then each phone must be re-paired before it can be used The system will display the message DELETE USERS?. with BLUE&ME™ again. To confirm, press the PRESET UP/OK button. Or, using voice interaction: Delete the phonebook In the USER DATA menu you can delete the phonebook , say “Settings”, wait for the tone then say Press the data that was downloaded to the system. “Delete users”. 1 64 BLUE&ME™ User’s Manual To delete the phonebook using manual interaction, pro- To download a paired mobile phone phonebook using manual interaction, proceed as follows: ceed as follows: Select DEL. PHONEBOOK and then press the PRESET Select PHONEBOOK and then press the PRESET UP/OK button. UP/OK button. The system will display the question DEL. PHONE- Or, using voice interaction BOOK?. To confirm, press the PRESET UP/OK button Press the button and say “Settings”, wait for the Or, using voice interaction: tone and then say “Download phonebook”. button and say “Settings” wait for the Add contacts Press the tone and then say “Delete phonebook”. To copy contacts from your mobile phone to the handsfree communication system using manual interaction, The system will ask “Delete copy of phonebook from proceed as follows: the system?” To confirm, say “Yes”. Select ADD CONTACTS and then press the PRESET Download the phonebook UP/OK button. If you chose not to download the phonebook during the phone pairing procedure, or if you recently deleted the Or, using voice interaction: current phonebook, the USER DATA option will be button and say “Settings”, wait for the Press the available in the PHONEBOOK menu. tone and say “Add Contacts”. BLUE&ME™ User’s Manual 65 Then follow the instructions given on your mobile phone Advanced Options To navigate to the ADV. OPTIONS menu using manual owner’s manual for transferring contacts. interaction, proceed as follows: Reset user data To reset all user data to the default values using manual Press the /MAIN button to open the Main Menu, then interaction, proceed as follows: select SETTINGS by pressing the PRESET UP/OK butSelect DELETE ALL and then press the PRESET UP/OK ton. button. Select ADV. OPTIONS and then press the PRESET The system will display the question “Delete all?”. To UP/OK button. confirm, press the PRESET UP/OK button. Within the ADV. OPTIONS menu you can access the device ID. Or, using voice interaction: button and say “Settings” , wait for the NOTE: This code is an 8-digit number (device ID) which Press the uniquely identifies the BLUE&ME™ system installed on tone and then say “Reset All”. your car and cannot be changed. The system will ask “Delete all data saved by users from the system?”. To confirm, say “Yes”. 1 66 BLUE&ME™ User’s Manual Accessing the Image ID Accessing the device ID To access the Image ID by manual interaction, proceed as To access the device ID by manual interaction, proceed as follows: follows: Select Image ID and then press the PRESET UP/OK Select device ID and then press the PRESET UP/OK button. button. The instrument panel display BLUE&ME™ Image ID code. will show your The instrument panel BLUE&ME™ device ID. display will show your Accessing the Application ID Media Player Settings To access the Application ID by manual interaction, Autoplay proceed as follows: When the Autoplay option is on, BLUE&ME™ will start Select Application ID and then press the PRESET UP/OK to play the audio files on your USB device as soon as you turn the ignition key ON. Once you activate this option, button. the first time you use the player, playback will start The instrument panel display will show your automatically. BLUE&ME™ Application ID code. BLUE&ME™ User’s Manual 67 To change the Autoplay setting using manual interaction, Shuffle Use the Shuffle option to change the playback sequence. proceed as follows: With the Shuffle option on, BLUE&ME™ will play Open the Main Menu, select MEDIA PLAYER, SETdigital audio files at random. TINGS, AUTOPLAY and then press the PRESET UP/OK To change the Shuffle setting using manual interaction, button. proceed as follows: To activate Autoplay, select AUTOPLAY ON and press the PRESET UP/OK button. To deactivate Autoplay, Open the Main Menu, select MEDIA PLAYER, SETselect AUTOPLAY OFF and press the PRESET UP/OK TINGS, SHUFFLE and then press the PRESET UP/OK button. button. To activate the Shuffle option, select SHUFFLE ON and press the PRESET UP/OK button. To deactivate it, select and say “Autoplay on” or “Autoplay SHUFFLE OFF and press the PRESET UP/OK button. Or, using voice interaction: Press the off”. Or, using voice interaction: NOTE: If you change the Autoplay settings after conbutton and say “Shuffle on” or “Shuffle necting the USB device, the new setting will be activated Press the the next time you connect a different USB device (or the off”. same USB device with an updated track library). 1 68 BLUE&ME™ User’s Manual Repeat Use the Repeat option to repeat a track. Exit the settings menu At the end of any of the operations described above, you can exit the SETTINGS menu as described below or the To activate the Repeat option using manual interaction, message will disappear from the display in less than proceed as follows: 10 seconds. Open the Main Menu, select MEDIA PLAYER, SETTo exit the SETTINGS menu using manual interaction: TINGS, REPEAT and then press the PRESET UP/OK button. Select EXIT and then press the PRESET UP/OK button. To activate the Repeat option, select REPEAT ON and BLUE&ME™ HANDS-FREE COMMUNICATION press the PRESET UP/OK button. To deactivate it, select SUPPORTED MOBILE PHONES REPEAT OFF and press the PRESET UP/OK button. BLUE&ME™ Hands-Free Communication supports your personal devices via Bluetooth威 wireless technolOr, using voice interaction: ogy and USB. and say “Repeat on” or “Repeat off”. Press the To get updated information about devices supported by NOTE: With the Repeat option on, the previous and BLUE&ME™ , contact a FIAT Dealership or consult the next commands will play the previous or next track and dedicated website at www.fiatusa.com. the new track will be repeated. BLUE&ME™ User’s Manual 69 Mobile Phones With Bluetooth姞 Wireless Technology BLUE&ME™ Hands-Free Communication supports most mobile phones with Bluetooth威 1.1 and Hands-Free 1.5 profile support (refer to the Bluetooth威 wireless connection specifications given in your mobile phone owner’s manual). “Pull” phones “Pull” phone means that your mobile phone supports automatic phonebook download with Bluetooth威 wireless technology, your whole phonebook will be automatically downloaded to BLUE&ME™ during the initial phone pairing procedure and updated every time your phone connects to BLUE&ME™. Due to the different software versions supported on mobile phones, certain functions (e.g., answering a second incoming phone call, transferring phone a phone call from hands-free communication system to mobile phone and vice versa, etc.) may not be supported as described in this manual. In any case, phone conversation using the hands-free communication package will not be impaired. To consult the list of mobile phones and functions supported, consult the dedicated website at www.fiatusa.com or Customer Services on 888-CIAO-FIAT (888-242-6342). “Push” phones (phonebook not automatically downloaded) “Push” phone means that your mobile phone supports single contact download with Bluetooth威 wireless technology. After the pairing process you will need to go to the USER DATA, ADD CONTACTS menu to send phonebook contacts from your mobile phone to BLUE&ME™. 1 70 BLUE&ME™ User’s Manual Mobile phones with message reader (not all Supported digital audio files The media player supports audio files with the following mobile phones support reading incoming SMS formats: messages) If your mobile phone can send messages through the Extension Audio Coding Bluetooth威 wireless technology, it is possible to read .wma Windows Media Audio Decode incoming messages using the BLUE&ME™ Hands-Free (Format Tag: WMA2 = 353, Communication Package, to store them in the dedicated WMA1=352) Decodes all CBR proinbox or to delete them. files from 5kbps to 192kbps, 8kHz to 48kHz, mono and stereo DeSupported USB Memory Devices codes all v9 CBR profiles, from 5kbps to 320kbps, 8kHz to 48kHz, USB Memory Devices mono and stereo Decodes all qualThe media player supports most USB memory devices. ity based, bit rate based and peak 1.0, 1.1 or 2.0. constrained VBR profiles Supports NOTE: It is not possible to use USB devices equipped WMA v1 and WMA v2 bit streams with a “password” function. BLUE&ME™ User’s Manual 71 Extension .mp3 .wav .aac Audio Coding MP3 in two forms: MPEG-1 Layer 3 (sampling rates 32 kHz, 44.1 kHz and 48 kHz) and MPEG-2 Layer 3 (16 kHz, 22.05 kHz and 24 kHz). Supports the proprietary Fraunhofer extension called “MP2.5”, which adds even lower sampling rates (8 kHz, 11.025 kHz and 12 kHz). ISO compliance with the following bitrates (kbps): 16, 32, 64, 96, 128, 192. Both Mono and Stereo. And Layer 3, VBR and CBR support. Digital audio file, without data compression. MPEG-4, M4A support Sampling rates: 8, 11, 16, 22, 24, 32, 44, 48 kHz Bitrates: 16, 32, 48, 64, 80, 96, 112, 128, 160, 192, 224, 256 kbps NOTE: The media player does not support audio files compressed with other formats and DRM (Digital Right Management) protected audio files. Non-supported audio files that may be present on the USB device will be ignored. 1 72 BLUE&ME™ User’s Manual Query-based playlists are not supported. Supported playlist formats The media player supports the following playlist forIf a file is not in the expected location a search for will not mats: be performed. • .m3u – file containing a list of tracks (release 1 and 2). For further details on how to build playlists for • .wpl – Windows威-based file containing a playlist. BLUE&ME™ , refer to PRACTICAL HINTS FOR USING (playlist capacity limit for this format is 300Kb). Play- THE MEDIA PLAYER. lists with extension.wpl can be built with Microsoft威 Windows Media威 Player. The media player does not support nested or linked playlists. Playlist tracks with relative and absolute paths are supported. BLUE&ME™ User’s Manual 73 1 74 BLUE&ME™ User’s Manual LIST OF AVAILABLE VOICE COMMANDS The following tables list the voice commands available on BLUE&ME™ Hands-Free Communication. The ⬙keyword⬙ for each voice command (e.g., the main voice command) and the synonyms that may be used are shown. BLUE&ME™ User’s Manual 75 1 76 BLUE&ME™ User’s Manual BLUE&ME™ User’s Manual 77 1 78 BLUE&ME™ User’s Manual BLUE&ME™ User’s Manual 79 1 80 BLUE&ME™ User’s Manual BLUE&ME™ User’s Manual 81 1 82 BLUE&ME™ User’s Manual BLUE&ME™ User’s Manual 83 TROUBLESHOOTING Hands-Free Communication Package General - display screen Problem Display screen shows: NO PHONEBOOK And the system says ⬙To copy the phone book to the system, go to the Settings Menu, and select USER DATA. To dial a number, say Dial.⬙ Probable Cause For “pull” phones • When the system asked “The data from the phonebook will now be copied onto the system. Continue?”, you responded with “No” • You have not downloaded your phonebook via the SETTINGS menu • The downloaded phonebook was deleted For “push” phones • You have not sent contacts to the system using the ADD CONTACTS procedure • The downloaded phonebook was deleted 1 Possible Solution For “pull” phones • Use the option PHONEBOOK in the SETTINGS menu to download the phonebook again • Enter contact information in the phonebook on your mobile phone and then download the phonebook again – see the section SETTING FUNCTIONS MANAGING USER DATA AND PHONEBOOK For “push” phones • Use the option ADD CONTACTS in the SETTINGS menu to send contacts in the phonebook on your mobile phone to the system – see the section SETTING FUNCTIONS - MANAGING USER DATA AND PHONEBOOK 84 BLUE&ME™ User’s Manual Problem Display screen shows: PHONEBK. EMPTY and the system says “Phone book empty. To add a new contact in the phone book, go to the Settings menu, and select User data. To dial a phone number, say Dial, followed by the number.” Probable Cause For “pull” phones • You answered “Yes” to “To use the phonebook, it is necessary to copy contacts to the system. Continue?” but the downloaded phonebook does not include any valid contacts • You have used the option PHONEBOOK in the SETTINGS menu, but the mobile phone phonebook does not include any valid contacts For “push” phones • You used the ADD CONTACTS option but did not send any valid contacts to the system Possible Solution For “pull” phones • Enter valid contact information (name and one phone number at least) in the phonebook on your mobile phone, then download the phonebook again – see the section SETTING FUNCTIONS MANAGING USER DATA AND PHONEBOOK For “push” phones • Use the option ADD CONTACTS in the SETTINGS menu to send contacts from your mobile phone to the system – see the section SETTING FUNCTIONS MANAGING USER DATA AND PHONEBOOK BLUE&ME™ User’s Manual 85 Problem Probable Cause Display screen shows: • The paired mobile phone is turned off NO PHONE • The paired mobile phone is not within And the system says range of the system (the mobile phone “No Bluetooth telephone should be located within approximately is connected.” 30 feet of the system) • Bluetooth威 wireless technology connection has been disabled on your mobile phone Problem Display screen shows: DISCONNECTED. Possible Solution • Turn the paired mobile phone on • Make sure that your phone is paired • Make sure that the Bluetooth威 wireless technology connection on your mobile phone is enabled • Make sure that the mobile phone you paired with the system is within range Probable Cause Possible Solution • A technical error occurred with the mo- • Reset BLUE&ME™ by turning the mobile phone Bluetooth威 wireless technolbile phone off and on ogy capabilities • Reset BLUE&ME™ by turning the igni• During an ongoing phone conversation, tion key to OFF and then to ON again the mobile phone was taken out of the system range 1 86 BLUE&ME™ User’s Manual Problem Probable Cause Display screen shows: • A technical error occurred during the PAIR. FAILED and the pairing procedure system says “Pairing unsuccessful. Please try again.” Display screen shows: PRIVATE NUMBER Possible Solution • Verify the correct PIN number, and try entering it again • Reset the mobile phone by turning it off and on, and then retry the pairing procedure – see the section SETTING FUNCTIONS - PAIRING YOUR MOBILE PHONE • The caller is not recognized as a name • Enter a contact in your mobile phonestored in the phonebook, or the paired book for the incoming call, and then mobile phone does not have a called ID download your phonebook or contact feature again • The caller has blocked caller ID to pre- • For phones with no caller ID support or for calls from callers with caller ID vent the system from displaying the caller’s name and/or phone number blocked, nothing can be done and the message will always appear BLUE&ME™ User’s Manual 87 Problem Probable Cause Display screen shows: • Even occasional short viewings of the ONLY AT REST and the car display may be hazardous if your system says: “This comattention has been diverted away from mand is available only your driving tasks. Certain when the vehicle is staBLUE&ME™ functions, which require tionary.” the user to give attention to the car display, are only available when the car is stopped The system did not re- • If you do not speak soon enough after spond to voice compressing the button, the system mand or key press will interrupt voice interaction If you are speaking too far from the in-car microphone (for example, if you are sitting in the back seat), the system may not hear your voice command • If you don’t wait for the tone after button, the system pressing the will get only a portion of the keyword and will not recognize it Possible Solution • Stop your car and attempt to perform the function again manually, or continue driving and perform the function using the voice recognition system • Press the button and pronounce the voice command again button and pronounce the • Press the voice command again /MAIN button and try the op• Press the eration again. Make sure to take action within approximately eight seconds after /MAIN button pressing the 1 88 BLUE&ME™ User’s Manual Problem The mobile phone prompts you to enter a PIN number, but no phone pairing procedure was running Probable Cause Possible Solution • If you don’t press the button before pronouncing a voice command, the system will not activate voice recognition and therefore will not recognize your voice commands /MAIN but• If you don’t press the ton to enter the Main Menu, it will not be possible to manually access the BLUE&ME™ menu /MAIN button, • If after pressing the you don’t take action within approximately eight seconds, the system will not respond to your key press • After you delete the pairing-related user • Select option DELETE USERS on the system information on your mobile phone or and delete all users; then, pair the phone on the system, the Bluetooth威 pairing again – see the section SETTING FUNCTIONS relationship between your mobile phone - MANAGING USER DATA AND PHONEand BLUE&ME™ will no longer work BOOK and also the section SETTING FUNCTIONS - PAIRING YOUR MOBILE PHONE BLUE&ME™ User’s Manual 89 Problem Probable Cause Possible Solution When in close proximity of the car, • Some types of mobile phones re• Refer to your mobile phone owner’s answering a phone call directly quire you to set the phone to manual to find out how to set up using the mobile phone “answer” choose between automatic incoming the default location for phone audio button, will automatically activate call transfer to the system or nonwhen a phone call is received the hands-free communication automatic incoming call transfer function (the caller’s voice is (you will transfer the call using the played through the car speakers) mobile phone keypad, as required) Pairing a paired mobile phone, • Before re-pairing with a mobile • Remember that the pairing procethe display screen shows: Pair. phone, information from the previdure will only need to be perfailed and the system says “Pairous pairing on BLUE&ME™ must formed once for your mobile phone. ing unsuccessful. Please try be deleted After this procedure, BLUE&ME™ again.” will automatically connect to your phone each time you get into the car and turn the ignition key to ON • To pair the phone again, select DELETE USERS and then re-pair the phone – see the section SETTING FUNCTIONS - MANAGING USER DATA AND PHONEBOOK and also the section SETTING FUNCTIONS PAIRING YOUR MOBILE PHONE 1 90 BLUE&ME™ User’s Manual Problem During the downloading of the phonebook from the mobile phone contacts, middle names/ initials, prefixes or suffixes are not recognized by the voice recognition system Probable Cause • The system does not support the use of prefixes, suffixes, or middle names/initials when calling contacts by voice Phone numbers containing inter- • On certain mobile phones, when national dialing codes (e.g., +39 downloading names and/phone Italy, +44 UK, +33 France, etc.) numbers to the hands-free commuare difficult to call nication system, the sign “+” is omitted Possible Solution • When calling contacts by voice, pronounce the contact’s name without using prefixes, suffixes or middle names/initials • If you have two entries with similar first and/or last names in your phonebook, modify one of the entries in the mobile phone to make it unique. Then, re-download the phonebook to the hands-free communication system • Replace “+” with “00” (e.g., +39 becomes 0039). BLUE&ME™ User’s Manual 91 To see the list of mobile phones and functions supported, consult the dedicated website www.fiatusa.com BLUE&ME™ or call Customer Services at 888-CIAOFIAT (888-242-6342). 1 Message Reader Problem I receive SMS messages on the cellular telephone but not on BLUE&ME™ Probable Cause • Not all cellular telephones support SMS messages transfer to BLUE&ME™ SMS texts received from your phone • Not all mobile phones support carrier service center show abnorcorrect transfer of the phone carrimal displaying of sender’s name or er’s name sending the SMS text to number BLUE&ME™ Possible Solution • Check that your cellular telephone supports the function for transmitting SMS Messages by technology or, for further information, refer to LIST OF TELEPHONE SETS SUPPORTED BY BLUE&ME™ , or visit the website www.fiatusa.com – 92 BLUE&ME™ User’s Manual Problem BLUE&ME™ stopped receiving messages from your cellular telephone Probable Cause • You may have set the notification type to Reader Off by mistake Possible Solution • Set, on menu notification settings, either AUDIO + VISUAL notification or VISUAL NOT notification – refer to READER FUNCTIONS SMS MESSAGES, NOTIFICATION SETTINGS paragraph Problem You cannot display some SMS messages, present on your cellular telephone, on BLUE&ME™ SMS message list Probable Cause • BLUE&ME™ is capable of reading and storing the last 20 received SMS messages while the telephone set is connected to the system. Messages received while not connected to the system are not transferred to BLUE&ME™ Possible Solution • SMS messages stored by BLUE&ME™ can be deleted – refer to READER FUNCTIONS SMS MESSAGES, SMS MESSAGES MANAGEMENT AND DELETING ALL SMS MESSAGES paragraphs BLUE&ME™ User’s Manual 93 Problem Probable Cause Possible Solution Some SMS messages or part of them • Some “special” characters within • In this case nothing can be done are not read, or are not correctly received SMS messages cannot be read by BLUE&ME™ hands-free interpreted by BLUE&ME™ communication package BLUE&ME™ SMS message reader • Probably, during the mobile • To download your cellular telephone pairing procedure step, you phone book from the Settings displays sender telephone number chose not to download the telemenu select the Copy Phonebook instead of sender name phone book, or, if your mobile or Add Contacts option – refer to SETTING FUNCTIONS, CELLUphone only supports management of single contacts, you chose to LAR TELEPHONE REGISTRATION and USER DATA MANdownload only some contacts AGEMENT paragraphs Sometimes received SMS message • Some SMS messages, e.g., the • In this case nothing can be done sender cannot be called ones sent by telephone operator, have no associated sender telephone number, so option CALL cannot be used 1 94 BLUE&ME™ User’s Manual Media Player Problem Displayed message: NO MEDIA and BLUE&ME™ says: “No media found” Probable Cause • No USB device is connected to the USB port in the car • No digital audio files are stored on the USB memory device • If power is interrupted, (e.g., car battery disconnection), BLUE&ME™ will rebuild the media library After connecting your USB device • Autoplay may be set to off and turning the ignition key to ON, no music is played Possible Solution • Connect your USB device to BLUE&ME™ • Store digital audio files on your USB memory devices following the instructions given by your media file software • Remove the USB device from the USB port and replace it to rebuild the media library again • Check whether your USB device is supported by BLUE&ME™ • Set Autoplay to on, remove and then replace the USB device • Press the button and say “Play⬙ Media playback should start BLUE&ME™ User’s Manual 95 Problem Probable Cause After inserting a USB device and • You may have used a USB device turning the car key to the ON posiwith the PASSWORD function tion, BLUE&ME™ malfunctions enabled occur. (e.g., failure to reproduce musical tracks or no voice messages) Problem Probable Cause Displayed message: NO PLAY• No playlist is stored on the USB LISTS and BLUE&ME™ says: “No device connected playlist found” Displayed message: PLAYLIST ER- • Playlist is damaged or invalid ROR and BLUE&ME™ says ⬙Playlist error” Possible Solution • Use another USB device without a password protection function Possible Solution • Build a playlist on your computer using your media file software and then copy it to your USB device • Make sure the playlist is in.m3u or.wpl format • Build the playlist again following the instructions given in BUILDING PLAYLISTS FOR BLUE&ME™ PRACTICAL HINTS • If the problem persists, delete the playlist from your USB device 1 96 BLUE&ME™ User’s Manual Problem Probable Cause Possible Solution Displayed message: EMPTY PLAY- • No media file information is con- • Delete the playlist from your USB LIST and BLUE&ME™ says: tained in the playlist device or copy media files to the • The.wpl file has exceeded the playlist using your media file soft“Empty playlist” BLUE&ME™ 300 kb memory ware • Reduce the number of tracks in the capacity limit playlist, using your media file soft• The playlist does not contain refware erences to media files on your USB device Problem Displayed message: FILE ERROR Probable Cause • ⬙One or more digital audio files are damaged or invalid Displayed message: PROTECTED • The track selected is DRMand BLUE&ME™ says: “Protected protected and it cannot be played by the media player content”. Possible Solution • Delete bad media from your USB device • In this case nothing can be done BLUE&ME™ User’s Manual 97 Problem Probable Cause BLUE&ME™ does not play all • Your playlist contains DRMprotected files that cannot be the digital audio files in the playplayed, or it contains references to list invalid media files The media library does not show • Your playlist contains DRM proall the digital audio files stored tected files that are ignored during on the USB device playback • Your playlist contains more than 20,000 tracks, that is the maximum number of files that can be copied to the media library • The playlist stored on your USB device contains more than 20 nested folders. Nested folders files will not be copied to the media library Possible Solution • For further details refer to “SUPPORTED USB MEMORY DEVICES” • Reduce the number of tracks on the USB device. • Reduce the number of nested folders on the USB device 1 98 BLUE&ME™ User’s Manual Problem Probable Cause Possible Solution After saying a command, • Certain commands are not avail• If the track is paused, resume playBLUE&ME™ says: “Command able when the track is paused or back by pressing the /ESC butthe CD player is playing a track not available”, although the comton. Then pronounce the voice mand you prompt is a first level command again voice command The same USB memory device • You removed the USB memory de- • To reset the USB memory device previously connected takes more vice from the PC before it was using Microsoft威 Windows威 XP, than 10 seconds to restart playready click on My Computer in the Start back on BLUE&ME™ menu, click rightward on the USB memory device, select Properties, select Tools, click on key “Check Now...” in field “Error-checking”, select “Automatically fix file system errors” and then click Start • To avoid future problems, remove the USB device using the option “Secure hardware removal” BLUE&ME™ User’s Manual 99 iPod姞 Problem iPod威 is not working (for iPod威 classic models prior to the 5th generation, the iPod威 Mini and iPod威 shuffle devices) iPod威 not working (for iPod威 classic models from the 5th generation forward, iPod威 Touch, and iPhone威 devices) Probable Cause • The iPod威 has not been enabled for use as a disc • It has been enabled for use as a disc but there are tracks inside in Mp4 format (these formats are not supported by BLUE&ME™ ) • There are DRM protected tracks on the iPod威 purchased from the iTunes site (the system does not support protected tracks such as those in DRM format that can be purchased from the iTunes store site) Possible Solution • Use an alternative USB memory stick or reset the iPod威 • Enable usage as a disc • Modify the track format to one that is compatible with BLUE&ME™ Use an alternative USB memory stick or reset the iPod威 1 100 BLUE&ME™ User’s Manual Problem Probable Cause iPod威 continues playing the • The repetition function for each indisame track or the “forward” vidual track may have inadvertently button has to be pressed to been activated move on to the next track • When browsing music by a selecting playback mode, the selected artist, album, genre or playlist may contain only 1 track. The iPod威 connected to the BLUE&ME™ is not charged • When the ignition is ON the car recharges the iPod威 unless the iPod威 is completely run down Possible Solution There is a specific item in the menu, like “continuous play” or “individual track repetition”, which must be deactivated Proceed with the deactivation: • press the controls activation button on the steering wheel • when requested by the system, say “Repeat Off” in a clear tone • wait for voice confirmation by the system which will say “Repeat Off” • wait for voice confirmation by the system which will say “Repeat Off” Select another playback mode or use the “Play Anything” voice recognition command • Remember that your iPod威 must have some charge or wait a few minutes until the system recharges it BLUE&ME™ User’s Manual 101 PERSONAL DATA PROTECTION BLUE&ME™ Hands-Free Communication functions entail personal data handling. In order to protect and to prevent non-authorized access to personal data, BLUE&ME™ has been implemented with the following criteria: CAUTION! Take into account that when leaving your car at a service center, personal data stored on BLUE&ME™ (phonebook and last calls) may be disclosed or may be subject to improper use. Before leaving your car at the service center you can delete stored data and phonebook from BLUE&ME™. • Personal data connected to hands-free communication functions (phonebook and last calls) can only be accessed after automatic recognition of your NOTE: For further details on how to delete personal Bluetooth威 wireless technology enabled mobile data and phonebook, refer to SETTINGS FUNCTION phone; MANAGING USER DATA • Stored personal data can be deleted using specific SYSTEM SOFTWARE USE NOTICE BLUE&ME™ functions. This system contains software that is licensed to ManuNOTE: For further details on how to delete personal facturer pursuant to a license agreement. Any removal, data, refer to SETTINGS FUNCTION - MANAGING reproduction, reverse engineering or other unauthorized USER DATA. use of the software from this system in violation of the license agreement is strictly prohibited and may subject you to legal action. 1 102 BLUE&ME™ User’s Manual − IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT (“EULA”), DO NOT USE THE DEVICE OR COPY THE SOFTWARE. INSTEAD, Hacking the BLUE&ME™ device or installing unapPROMPTLY CONTACT FIAT AUTO S.p.A. FOR INproved software may lead to warranty voiding and STRUCTIONS ON RETURN OF THE UNUSED DEcompromises of safety and of the security of stored VICE(S). ANY USE OF THE SOFTWARE, INCLUDinformation. ING BUT NOT LIMITED TO USE ON THE DEVICE, WILL CONSTITUTE YOUR AGREEMENT TO THIS END USER LICENSE AGREEMENT (“EULA”) EULA (OR RATIFICATION OF ANY PREVIOUS − You have acquired a device (“DEVICE”) which inCONSENT). cludes software licensed by FIAT Auto S.p.A. from one or more software licensors (“FIAT Auto S.p.A.’s Soft- GRANT OF SOFTWARE LICENSE. This EULA ware Suppliers”). Such software products, as well as grants you the following license: associated media, printed materials, and “online” or − You may use the SOFTWARE as installed on the electronic documentation (“SOFTWARE”) are proDEVICE. tected by international intellectual property laws and treaties. The SOFTWARE is licensed, not sold. All rights reserved. WARNING! BLUE&ME™ User’s Manual 103 DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS versions (e.g., in the user documentation and in the software). Even if you receive multiple versions of the EULA, you are licensed to use only one (1) copy of the SOFTWARE. − Speech Recognition. The SOFTWARE includes speech recognition component(s), you should understand that speech recognition is an inherently statistical process − No Rental. Except as authorized by FIAT Auto S.p.A., you may not rent, lease, or lend the SOFTWARE. and that recognition errors are inherent in the process. Neither FIAT Auto S.p.A. nor its suppliers shall be − SOFTWARE Transfer. You may permanently transfer liable for any damages arising out of errors in the all of your rights under this EULA only as part of a sale speech recognition process. or transfer of the DEVICE, provided you retain no − Limitations on Reverse Engineering, Decompilation copies, you transfer all of the SOFTWARE (including and Disassembly. You may not reverse engineer, all component parts, the media and printed materials, decompile, or disassemble the SOFTWARE, except any upgrades, this EULA and, if applicable, the Cerand only to the extent that such activity is expressly tificate(s) of Authenticity), and the recipient agrees to permitted by applicable law notwithstanding this limithe terms of this EULA. If the SOFTWARE is an tation. upgrade, any transfer must include all prior versions of the SOFTWARE. − Single EULA. The end user documentation for the DEVICE may contain multiple versions of this EULA, such as multiple translations and/or multiple media 1 104 BLUE&ME™ User’s Manual − Termination. Without prejudice to any other rights, − Internet-Based Services Components. The SOFTFIAT Auto S.p.A. or FIAT Auto S.p.A.’s Software WARE may contain components that enable and faciliSuppliers may terminate this EULA if you fail to tate the use of certain Internet-based services. You comply with the terms and conditions of this EULA. In acknowledge and agree that FIAT Auto S.p.A.’s Softsuch event, you must destroy all copies of the SOFTware Suppliers, their affiliates and/or their designated WARE and all of its component parts. agent may automatically check the version of the SOFTWARE and/or its components that you are uti− Consent to Use of Data. You agree that FIAT Auto lizing and may provide upgrades or supplements to S.p.A.’s Software Suppliers, their affiliates and/or the SOFTWARE that may be automatically downtheir designated agent may collect and use technical loaded to your DEVICE. information gathered in any manner as part of product support services related to the SOFTWARE. FIAT Auto − Additional Software/Services. The SOFTWARE may permit FIAT Auto S.p.A., FIAT Auto S.p.A.’s Software S.p.A.’s Software Suppliers, their affiliates and/or Suppliers, their affiliates and/or their designated their designated agent may use this information solely agent to provide or make available to you SOFTWARE to improve their products or to provide customized updates, supplements, add-on components, or services or technologies to you. FIAT Auto S.p.A.’s Internet-based services components of the SOFTSoftware Suppliers, their affiliates and/or their desigWARE after the date you obtain your initial copy of the nated agent may disclose this information to others, SOFTWARE (“Supplemental Components”). but not in a form that personally identifies you. BLUE&ME™ User’s Manual 105 • If FIAT Auto S.p.A. provides or makes available to you Supplemental Components and no other EULA terms are provided along with the Supplemental Components, then the terms of this EULA shall apply. • If FIAT Auto S.p.A.’s Software Suppliers, their affiliates and/or their designated agent make available Supplemental Components, and no other EULA terms are provided, then the terms of this EULA shall apply, except that the FIAT Auto S.p.A.’s Software Suppliers or affiliate entity providing the Supplemental Component(s) shall be the licensor of the Supplemental Component(s). • FIAT Auto S.p.A., FIAT Auto S.p.A.’s Software Suppliers, their affiliates and/or their designated agent reserve the right to discontinue any Internetbased services provided to you or made available to you through the use of the SOFTWARE. • Links to Third Party Sites. The SOFTWARE may provide you with the ability to link to third party sites through the use of the SOFTWARE. The third party sites are not under the control of FIAT Auto S.p.A.’s Software Suppliers, their affiliates and/or their designated agent. Neither FIAT Auto S.p.A.’s Software Suppliers nor their affiliates nor their designated agent are responsible for (i) the contents of any third party sites, any links contained in third party sites, or any changes or updates to third party sites, or (ii) webcasting or any other form of transmission received from any third party sites. If the SOFTWARE provides links to third party sites, those links are provided to you only as a convenience, and the inclusion of any link does not imply an endorsement of the third party site by FIAT Auto S.p.A.’s Software Suppliers, their affiliates and/or their designated agent. 1 106 BLUE&ME™ User’s Manual UPGRADES AND RECOVERY MEDIA − If the SOFTWARE is provided by FIAT Auto S.p.A. separate from the DEVICE on media such as a ROM chip, CD ROM disk(s) or via web download or other means, and is labeled “For Upgrade Purposes Only” you may install one (1) copy of such SOFTWARE onto the DEVICE as a replacement copy for the existing SOFTWARE, and use it in accordance with this EULA, including any additional EULA terms accompanying the upgrade SOFTWARE. licensed, not sold. You may not copy the printed materials accompanying the SOFTWARE. All title and intellectual property rights in and to the content which may be accessed through use of the SOFTWARE is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants you no rights to use such content. All rights not specifically granted under this EULA are reserved by FIAT Auto S.p.A.’s Software Suppliers, their affiliates and suppliers. Use of any online services which may be accessed through the SOFTWARE may be governed by the respective terms of use relating to such services. If this SOFTWARE contains documentation that is provided only in electronic form, you may print one copy of such electronic documentation. INTELLECTUAL PROPERTY RIGHTS All title and intellectual property rights in and to the SOFTWARE (including but not limited to any images, photographs, animations, video, audio, music, text and “applets,” incorporated into the SOFTWARE), the accompanying printed materials, and any copies of the SOFTEXPORT RESTRICTIONS WARE, are owned by FIAT Auto S.p.A.’s Software SupYou acknowledge that the SOFTWARE is subject to U.S. pliers, their affiliates or suppliers. The SOFTWARE is and European Union export jurisdiction. You agree to BLUE&ME™ User’s Manual 107 comply with all applicable international and national − No Liability for Certain Damages. EXCEPT AS PROlaws that apply to the SOFTWARE, including the U.S. HIBITED BY LAW, FIAT AUTO S.p.A’S SOFTWARE Export Administration Regulations, as well as end-user, SUPPLIERS AND THEIR AFFILIATES SHALL HAVE end-use and destination restrictions issued by U.S. and NO LIABILITY FOR ANY INDIRECT, SPECIAL, other governments. CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR IN CONNECTION WITH THE − TRADEMARKS. This EULA does not grant you any USE OR PERFORMANCE OF THE SOFTWARE. THIS rights in connection with any trademarks or service LIMITATION SHALL APPLY EVEN IF ANY REMEDY marks of FIAT Auto S.p.A., FIAT Auto S.p.A.’s SoftFAILS OF ITS ESSENTIAL PURPOSE. IN NO EVENT ware Suppliers, their affiliates or suppliers. SHALL FIAT AUTO S.p.A’S SOFTWARE SUPPLIERS − PRODUCT SUPPORT. Product support for the SOFTAND/OR THEIR AFFILIATES BE LIABLE FOR ANY WARE is not provided by FIAT Auto S.p.A.’s Software AMOUNT IN EXCESS OF U.S. TWO HUNDRED Suppliers, or their affiliates or subsidiaries. For prodFIFTY DOLLARS (U.S.$250.00). uct support, please refer to FIAT Auto S.p.A. support − FOR APPLICABLE LIMITED WARRANTIES AND number provided in the documentation for the DESPECIAL PROVISIONS PERTAINING TO YOUR VICE. Should you have any questions concerning this PARTICULAR JURISDICTION, PLEASE REFER TO EULA, or if you desire to contact FIAT Auto S.p.A. for YOUR WARRANTY BOOKLET INCLUDED WITH any other reason, please refer to the address provided THIS PACKAGE OR PROVIDED WITH THE SOFTin the documentation for the DEVICE. WARE PRINTED MATERIALS. 1 108 BLUE&ME™ User’s Manual QUICK TIPS – FREQUENTLY ASKED QUESTIONS What Can I Do With My BLUE&ME™ Hands-Free Communication Package? • Make phone calls using BLUE&ME™ Hands-Free Communication BLUE&ME™ Hands-Free Communication – Quick Tips • If I have questions and cannot find the answer in the BLUE&ME™ User’s Guide, is there anyone I can call? − Yes, you can contact the FIAT Customer Center at 1-888-CIAO-FIAT (1-888-242-6342). • Listen to music from a USB stick or iPod威 through the • If I know the series of commands I wish to make, is BLUE&ME™ Media Player there a way to avoid the voice command prompts? • Read SMS Text Messages communicated through the BLUE&ME™ Message Reader (only available with − Yes, it is called barging in. Simply press the certain mobile phones) steering wheel button and say your first command, then immediately after, press the steering wheel • Control your FIAT TomTom PND (Personal Navigabutton again and say your second command. tion Device) (If Equipped) − Example – Press the steering wheel button and say “Settings”, then as soon as you hear the beep, steering wheel button again and say press the “Pairing”. BLUE&ME™ User’s Manual 109 • Every time I get in the vehicle, my mobile phone alerts • The BLUE&ME™ VR (Voice Recognition) Speech volme or notifies me about connecting to BLUE&ME™ , ume is Too Loud/Too Quiet. but I’ve already paired my mobile phone. − This is a customer selectable feature. To change the Speech volume, Press the MENU button on the Radio. − The issue needs to be fixed through your phone settings. You need to set your phone to not prompt you The use the Up and Down arrows to select the Speech Volume setting. Use the Right and Left arrows to with this request “never prompt, never ask the question, or trusted source” – This will allow you to increase or decrease the Speech volume. automatically reconnect the next time. • The BLUE&ME™ VR (Voice Recognition) system fails • Why am I not able to pair my mobile phone? to make the proper selection when I give the command. − Most devices are supported. However, you should − Attempt to change the tone/syllables or say the refer to the list of supported phones/blackberries at command the same way the system says it. the www.fiatusa.com website, and click the BLUE&ME™ icon. Or contact the FIAT Customer • The BLUE&ME™ VR (Voice Recognition) Center at 1-888-CIAO-FIAT (1-888-242-6342) to make commands/options are not in normal speech, can I sure your mobile phone is supported. change the voice? − No, the voice is an electronic synthesized voice, and cannot be changed. 1 110 BLUE&ME™ User’s Manual • Can I have 2 phones both paired to the BLUE&ME™ BLUE&ME™ Media Player – Quick Tips system at the same time? • How do I use the BLUE&ME™ Media Player? There − Yes, you can pair up to a total of 5 phones, but only are three methods: one can be linked at anytime. The most recently paired − Voice Recognition mobile phone will be the primary phone. − Steering Wheel Buttons (located on the front and • Why does the BLUE&ME™ system say “phonebook rear of the steering wheel) copy in progress” when I first try to make a call after − Using the controls on the device itself getting into the vehicle? − Depending on the size of your phonebook, • Why is the USB Port and AUX Port in the glove box? BLUE&ME™ may take some time to download or − To provide you more security for your personal check for updates. So, if you try to immediately make media devices. Even though your media device is in a phone call after getting into the vehicle, the the glove box you can still operate that device by use BLUE&ME™ system may tell you to wait. of the Steering Wheel Buttons. • My iPod威/iPhone is not recognized by the Media Player System, or is recognized, then lost. BLUE&ME™ User’s Manual 111 − Insure that the software on your iPod威/iPhone is up BLUE&ME™ Message Reader – Quick Tips to date and contact your local FIAT Dealership for • The BLUE&ME™ SMS Text Message Reader does not possible software updates to the BLUE&ME™ system. appear to be working? • The USB begins to play regardless of the last source I − This feature is only available on select mobile had selected. phones. Please refer to the list of supported phones on − With the AUTOPLAY feature turned on, the system the www.fiatusa.com website, and select the will always switch to the USB device if a device is BLUE&ME™ icon. Or contact the FIAT Customer already plugged in. Center at 1-888-CIAO-FIAT (1-888-242-6342) • The volume changes significantly when I switch between the Media Player and AM/FM/SAT ? − The audio level depends on the quality of the music and how the music was recorded onto the media device. 1 112 BLUE&ME™ User’s Manual BLUE&ME™ And The TomTom PND (Portable Navigation Device) (If Equipped) – Quick Tips • How does the TomTom Portable Navigation Device communicate with the BLUE&ME™ system? − You use the same procedure as if you were pairing a mobile phone to the BLUE&ME™ system. Once connected, you can control your PND by using the BLUE&ME™ system Voice Commands and steering wheel buttons. Also, the BLUE&ME™ system can be controlled from the Tom Tom PND. • How do I mount my TomTom PND on the dash? − Insert the TomTom PND in the cradle holder then insert the cradle holder into the spring loaded slot on the dash. VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation. WARNING! Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive. This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle. Chrysler Group LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured. INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible. The negative power connection should be made to body sheet metal adjacent to the negative battery connection. This connection should not be fused. Antennas for two-way radios should be mounted on the roof or the rear area of the vehicle. Care should be used in mounting antennas with magnet bases. Magnets may affect the accuracy or operation of the compass on vehicles so equipped. The antenna cable should be as short as practical and routed away from the vehicle wiring when possible. Use only fully shielded coaxial cable. Carefully match the antenna and cable to the radio to ensure a low Standing Wave Ratio (SWR). Mobile radio equipment with output power greater than normal may require special precautions. All installations should be checked for possible interference between the communications equipment and the vehicle’s electronic systems. Copyright © 2011 Chrysler Group LLC 872214.ps 12FF500-126-AA Fiat 1" gutter 10/04/2010 11:37:45 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation. WARNING! Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive. This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle. Chrysler Group LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured. Copyright © 2011 Chrysler Group LLC INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible. The negative power connection should be made to body sheet metal adjacent to the negative battery connection. This connection should not be fused. Antennas for two-way radios should be mounted on the roof or the rear area of the vehicle. Care should be used in mounting antennas with magnet bases. Magnets may affect the accuracy or operation of the compass on vehicles so equipped. The antenna cable should be as short as practical and routed away from the vehicle wiring when possible. Use only fully shielded coaxial cable. Carefully match the antenna and cable to the radio to ensure a low Standing Wave Ratio (SWR). Mobile radio equipment with output power greater than normal may require special precautions. All installations should be checked for possible interference between the communications equipment and the vehicle’s electronic systems. 2012 500 2012 OWNER’S MANUAL Chrysler Group LLC 12FMB-726-AE 5th Edition 500 Printed in U.S.A. 872214.ps 12FF500-126-AA Fiat 1" gutter 10/04/2010 11:37:45 2012 500 2012 OWNER’S MANUAL Chrysler Group LLC 12FF500-126-AA First Edition Printed in U.S.A. 500